Can 14 Gauge Wire Power LED Flood Lights on Trailer

Question

Question:

Hi There. Looking to add two LED flood lights on to a travel trailer. Currnetly have wires run with no marking to aswitch mounted on a light. Plan to remove the existing light and install a stand alone switch that will control the two flood lights for night time trailer parking. Is a jackets 14 gauge 2 wire acceptable for this install?

asked by: Keith P

0

Expert Reply:

Since LED lights like the Low Profile LED Flood Light part # 3371492135 that you referenced draw such a low amount of amperage 14 gauge wire would work fine.

expert reply by: Jameson C

0

Answer 1

I can confirm for you that each of the parts you mentioned will indeed work together: - GloLight LED Backup Light #BUL111CB - PVC Grommet #a70gb - 2-Wire Pigtail #A45CB - Mounting Bracket #337LB1 I have added some links to video reviews for you to…

view full answer...

Answer 2

To add additional backup lights like GloLight LED Backup Light for Truck or Trailer - Submersible - 22 Diodes - Oval - Clear Lens - Qty 1 #BUL111CB, you will want to splice into the reverse function wire on your trailer. For a 7-way, this is…

view full answer...

Answer 3

According to Buyers Products, their #3371492135 Low Profile LED floodlight is not submersible. If the lamp was submerged it would be damaged. We do however have an alternative. I'd recommend using part #BUL111CB, along with the #A70GB grommet and…

view full answer...

Answer 4

There are no white, oval LED tail lights we carry which have a curved face. We do carry the 22 diode GloLight LED Backup Light #BUL111CB which is submersible but you would need to make your own mounting spot as it is a recess mount that also requires…

view full answer...

Answer 5

The diodes are actually the only things that light up on the GloLight LED Backup Light #BUL111CB. So when they light up the ring technically lights up (see attached photo). We do have the surface mount version as part #BUL111CFPG!

view full answer...

Answer 6

The #STL22CCRB lamp you referred to is typically mounted in a grommet, like part #A70GB, which in turn is mounted in a bracket like part #337LB1SS. If you were planning on cutting a hole to mount the lamp and grommet, the hole will need to measure…

view full answer...

Answer 7

The Mounting Bracket for 6-1/2" Oval Trailer Tail Lights part #337LB1SS is designed to work with a trailer tail light that measures 6-1/2" long x 2-1/4" tall. I saw there were some Grote Oval Trailer Tail Lights that match these…

view full answer...

Answer 8

I went out to the warehouse and measured a Mounting Bracket for 6-1/2" Oval Trailer Tail Light - Stainless Steel Item #337LB1SS. The internal dimensions of the large oval opening are 6-3/4 inches long by 2-1/2 inches tall.

view full answer...

Answer 9

Trailer wiring generally uses 16 gauge wire, part #16-1-1. However, with a long trailer like yours you may want to go with a larger like 14 gauge #DW07550-1 or even 12 gauge #12-1-1. Each size is sold by the foot. You will need to have the lights at…

view full answer...

Answer 10

I did some checking and the hub/drum we offer that will work for you is the part #8-430-5UC3. This uses the same bearings as the 8-415 and will be an exact fit aside from the fact this is a non-ABS setup and the 8-415 came in an ABS setup and non-ABS…

view full answer...

Answer 11

I've never heard of an actual third brake light connector on a camper shell to plug in on a truck and we don't carry any parts to do that. The light generally needs to be hardwired into the truck's brake light circuit. The issue with this…

view full answer...

Answer 12

You will need the Red LED Trailer Clearance or Side Marker Light #328-K-52 or Amber LED Trailer Clearance or Side Marker Light #328-K-51 for your 2018 Forest River Sunseeker motorhome. These lenses have the same Top Command SAE-AP2-16 markings on the…

view full answer...

Can 14 Gauge Wire Power LED Flood Lights on Trailer

Product Page this Question was Asked From

Continue Researching