Can An Aftermarket Trailer Hitch Be Installed On a 2007 Toyota Tundra If Bumper Is Replaced
Question:
I have done a lot of salt water boat-launching with my 2007 Tundra and my rear bumper and factory hitch need to be replaced. Toyota recently put a brand new frame in my truck due to a frame defect, so it should be possible to get some more good years out of the truck. Many of the class 5 hitches you carry state they won’t fit trucks with “factory installed hitches”. Am I correct to assume this is because one would have to also replace the bumper? Since my intention is to buy a cheaper after market bumper anyhow Will I be able to use one of these class 5 hitches? Thanks!
asked by: Rich H
Expert Reply:
The factory trailer hitch options for a 2007 Toyota Tundra are tied into the rear bumper helping to provide extra support. This is why the factory trailer hitch cannot be replaced with an aftermarket trailer hitch as these do not tie into the bumper. However, if you were to remove the factory bumper in light of any aftermarket bumper you could then install an aftermarket hitch like the Curt Trailer Hitch Receiver part # C15398.
Product Page this Question was Asked From
Curt Trailer Hitch Receiver - Custom Fit - Class V - 2"
- Trailer Hitch
- Custom Fit Hitch
- Class V
- 2400 lbs TW
- 16000 lbs GTW
- 17000 lbs WD GTW
- 2 Inch Hitch
- 2400 lbs WD TW
- Visible Cross Tube
- CURT
more information >
Featured Help Information
Instructions
Continue Researching
- Shop: Trailer Hitch
- Shop: Curt Trailer Hitch Receiver - Custom Fit - Class V - 2"
- Video: Trailer Hitch Installation - 2013 Toyota Tundra - Curt
- Q&A: Will the Draw-Tite Hitch Replace the Factory Hitch On a 2010 Toyota Tundra With Aftermarket Bumper
- Shop: Curt Rebellion XD Shock Absorbing Adjustable Ball Mount w/ 2" and 2-5/16" Balls - 20K
- Shop: Curt Rebellion XD Shock Absorbing Adjustable Ball Mount w/ 2" and 2-5/16" Balls - 15K
- Search Results: curt ball mount only
- Article: 5 Things to Know About Weight Distribution Hitches
- Video: Review of Equal-i-zer Inner Link Plate for 8 Inch Trailer Frames - EQ90-02-5208
- Q&A: Will The Rock Tamers Mud Flap System Fit On A Shocker Hitch HD Ball Mount
- Search Results: gen y torsion
- Video: Trailer Hitch Installation - 2014 Dodge Ram 2500 - Curt
- Shop: Gen-Y Adjustable 2-Ball Mount w/ Stacked Receivers - 2-1/2" Hitch - 6" Drop/Rise - 21K
- Shop: Curt Trailer Hitch Receiver - Custom Fit - Class V Commercial Duty - 2-1/2"
- Shop: Draw-Tite Ultra Frame Trailer Hitch Receiver - Custom Fit - Class V - 2"
- Shop: Shocker Hitch HD Ball Mount - 2-5/16" Ball - 2-1/2" Hitch - 1-1/2" Drop -20K
- Shop: Trailer Wiring
- Q&A: Can a Weight Distribution System be Used on an I Beam Trailer
- Q&A: Weight Distribution System For Hauling a Dump Trailer
- Q&A: Will the Curt Class V Trailer Hitch Fit on a 2010 Toyota Tundra TRD
- Q&A: Comparing Gen-Y Torsion Cushioned Ball Mount and Curt Rebellion XD
- Q&A: hitch upgrade for 2007 toyota tundra extended cab 4x4
- Search Results: pk12711u
- Search Results: receiver
- Video: Hopkins Custom Fit Vehicle Wiring - Trailer Hitch Wiring - HM11143395 Review
- Shop: Tonneau Cover
Todd
5/18/2024
But do you sell the adapter part to reconnect the bumper to the hitch? Looks like I could have something fabricated but could be expensive.