Tekonsha Primus Brake Controller Showing SH Error Code When Trailer is not Connected
Question:
code flashing on brake controler is s h the book says there is a short in wiring but it flashes with and with out trailer hooked up
asked by: Frank J
Expert Reply:
The SH error code indicates a short circuit in the brake controller output. Since it is occurring when the trailer is not connected, it would eliminate the trailer wiring as being the problem.
The trailer connector itself is the usual suspect in this case. Check the connector for damage or corrosion. If you can see any white or green corrosion on the pins of the connector, there is a good chance that the corrosion has spread to the interior of the connector, where the wiring connects to the terminals. If this corrosion becomes severe enough and builds up on the terminals, it can cause a short to an adjacent terminal.
If the connector checks out okay, locate the blue wire exiting the rear of the controller. Sever the wire several inches rearward of the controller (so there is plenty of available wire to reconnect it). If cutting the wire solves the problem, the short exists somewhere in the wiring between the connector and the brake controller. You can trace the wire if you care to, looking for loose connections or worn or cracked insulation, but this might be difficult depending on the vehicle. Your best bet might be to simply tap in a length of 10 gauge wire like # 10-1-1 and run it from the blue wire on the controller to the # 2 terminal on the connector. This would bypass the defective wire.
Products Referenced in This Question
Product Page this Question was Asked From
Tekonsha Prodigy P3 Trailer Brake Controller - 1 to 4 Axles - Proportional
- Trailer Brake Controller
- Proportional Controller
- Electric
- Electric over Hydraulic
- Automatic Leveling
- Under-Dash Box
- Dash Mount
- Up to 4 Axles
- LCD Display
- Up to 360 Degrees
- Tekonsha
more information >
Featured Help Information
Instructions
Miscellaneous Media
Continue Researching
- Shop: Brake Controller
- Shop: Universal Installation Kit for Trailer Brake Controller - 7-Way RV and 4-Way Flat - 10 Gauge Wires
- Shop: 10 Gauge Primary Wire - Blue - per Foot
- Shop: Tekonsha Prodigy P3 Trailer Brake Controller - 1 to 4 Axles - Proportional
- Shop: Curt Venturer NEXT Trailer Brake Controller - 1-3 Axles - Time Delayed
- Shop: Trailer Wiring
- Article: Towing a Trailer? Let's Talk About Brake Controllers
- Article: Troubleshooting Brake Controller Installations
- Q&A: Hopkins Impulse Brake Controller Showing E1/E2 Error Code
- Q&A: Tracing Intermittent Short In Trailer Braking System
- Shop: Trailer Hitch
- Q&A: What is the Difference Between a 4-Way and 7-Way Trailer Connector
- Video: Choosing the Right Trailer Wiring
- Search Results: brake controller
- Article: Brake Controller 7- and 4-Way Installation Kit (ETBC7)
- Search Results: trailer brake controller
- Article: Trailer Wiring Diagrams
- Shop: Redarc Tow-Pro Liberty Brake Controller - Dash Knob - 1 to 2 Axles - Proportional
- Video: Choosing the Right Brake Controller
- Q&A: What is the Difference Between a Class II and a Class III Hitch?
- Search Results: etbc7
- Article: How to Choose the Right Trailer Hitch Class
- Video: Redarc Tow-Pro Liberty Brake Controller Review RED24FR
- Q&A: My Vehicle has a 4-Pin Trailer Plug, but Trailer has 7-Pin Trailer Plug
- Search Results: 90160
- Q&A: Picking Between ETBC7 and ETBC7L for Brake Controller Install
- Article: Brake Controller Installation: Starting from Scratch
- Shop: Gooseneck Hitch
- Shop: Curt Powered Tail Light Converter with 4-Pole Flat Trailer Connector
- Search Results: 90885
Shaun H.
3/16/2024
Mike, I am having the same issue as Frank on my 1994 K1500. I installed the 7 pin harness pt#ETBC7 and the tekonsha p2 brake controller pt#90885 step by step from the etrailer video. I then had the same SH error code. I double checked all connections and the brand new 7 pin terminal all is well. I even ran a new blue wire from the 7 pin terminal to the blue wire on the brake controller with the same issue. Is it likely that the trailer brake controller is faulty right out of the box? Thanks, Shaun Hammond.