Hitch that Fits 2011 Ford Flex and 2013 Volkswagen Routan SE

Question

Question:

Hitch #13364 Will this item fit both 2011 Ford Flex SEL And also fit a 2013 Volkswagon Routan SE... ???

asked by: Jeremy W

0

Expert Reply:

The hitch part # 13364 that you referenced does fit the 2013 Volkswagen Routan as long as it's a Canadian market model. For the 2011 Ford Flex you'd then want the part # e52AR if it has Dual exhaust and # e95KR for single exhaust and you'd be set. There isn't a hitch that fits both vehicles.

expert reply by: Jameson C

0

Answer 1

There is no difference between the Universal Tow Bar Adapter for Roadmaster Direct-Connect Baseplate #RM62ZR, and Roadmaster's 039-2. The part number #RM62ZR is just our part number for our system, and 039-2 is Roadmaster's part number, but…

view full answer...

Answer 2

You are correct. The Universal Tow Bar Adapter for Roadmaster Direct-Connect Baseplate #RM62ZR (039-2) should only be used with a triple lug attachment and not a single lug. The adapter will still work with Blue Ox, Curt, etrailer, and Demco tow…

view full answer...

Answer 3

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 4

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 5

If the trailer wheels scrubbed (dragged and scrapped the ground instead of rolling) when jack knifed then it could have thrown something out of alignment or damaged something. First, inspect the suspension. Look for any elongated holes where…

view full answer...

Answer 6

I've never heard of an actual third brake light connector on a camper shell to plug in on a truck and we don't carry any parts to do that. The light generally needs to be hardwired into the truck's brake light circuit. The issue with this…

view full answer...

Answer 7

From what I could find it looks like your 122R (red) and 122Y (amber) lights measure 3.75" x 1.70" x .81". We don't have any replacement lense directly for the GLO-BRITE lights but we do have some similar lights that you could use…

view full answer...

Answer 8

Seal 171255UC has an inner diameter of 1.719 inches and outer diameter of 2.565 inches. A seal that has those dimensions would actually be #58846. I've added a link to a video review of this seal for you to take a look at.

view full answer...

Answer 9

Brake systems are not dependent on the hub bolt pattern. So you can use the Electric Trailer Brake Kit #AKEBRK-7-SA for 12 inch hub/drums or #AKEBRK-35-SA for 10 inch hub/drums. Then use #10-1-1 wire sold by the foot for your brake magnet wiring.…

view full answer...

Answer 10

While we may have an option for you, we do not have the exact specs on your Allis grease seal part number 5013 29772. However, with the 1.6" ID and 2.5" OD measurements you provides, that is very close to our #58846. This particular grease…

view full answer...

Answer 11

Normal operating temperatures for drum brakes range from 150-400 degrees F. During certain stopping conditions the brake heat can exceed 600 degrees. The effectiveness and stopping power of the brakes is significantly reduced at these higher…

view full answer...

Answer 12

If you are needing the hub and drum assembly then you will want to go with the Dexter Trailer Hub and Drum Assembly #8-201-5UC3-EZ but if you are just looking for an idler hub then you will want part #8-213-5UC1 instead. These come with the correct…

view full answer...

Hitch that Fits 2011 Ford Flex and 2013 Volkswagen Routan SE

Products Referenced in This Question

Product Page this Question was Asked From

Featured Help Information

Instructions

Continue Researching