Sub and Amp Combo to Use with RV Stereo

Question

Question:

I bought this unit. Would like to know the subwoofer you recommend that will work with this unit as it is now? Thanks

asked by: Paul T

0

Expert Reply:

The iRV stereo part # 292-101079 that you referenced can be used with a subwoofer but you'd need to install an amp too as it does not have the wattage to power a sub as-is. The great news though is that we have subs with included amps like the Jensen 200 watt sub part # JMPSW800 which take out the guesswork of picking out a matching amp and sub and also make for an easier install.

expert reply by: Jameson C

0

Answer 1

I have included a picture showing how the motor and switch wire up on the Lippert stabilizer jack #LC298707.

view full answer...

Answer 2

Yes, the audio outputs on the Jensen stereo jwm70a are RCA outputs that can be used with an amplifier and then a subwoofer. You could also use an amplified subwoofer like Jensen Enclosed Amplified Marine Subwoofer - Surface Mount part #JMPSW800 which…

view full answer...

Answer 3

The wiring harness for the Jensen Enclosed Amplified Marine Subwoofer #JMPSW800 has a 3-wire pigtail for you to splice in your power, ground, and remote. You would just need to cut the wire down to necessary length and splice it to the remote wire…

view full answer...

Answer 4

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 5

The manual lockout on your Atwood 85778 surge brake coupler is there so that you can back up the trailer without the brakes locking up on you. Yes you can safely tow your trailer with the broken manual lockout, you just have to make sure you…

view full answer...

Answer 6

Seal 171255UC has an inner diameter of 1.719 inches and outer diameter of 2.565 inches. A seal that has those dimensions would actually be #58846. I've added a link to a video review of this seal for you to take a look at.

view full answer...

Answer 7

What you need for your Isuzu NPR truck is a powered converter #C59236. It is compatible with incandescent and LED trailer lights. I have included a link to the installation instructions for you. This harness does require a direct connection to the…

view full answer...

Answer 8

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 9

If the trailer wheels scrubbed (dragged and scrapped the ground instead of rolling) when jack knifed then it could have thrown something out of alignment or damaged something. First, inspect the suspension. Look for any elongated holes where…

view full answer...

Answer 10

From what I could find it looks like your 122R (red) and 122Y (amber) lights measure 3.75" x 1.70" x .81". We don't have any replacement lense directly for the GLO-BRITE lights but we do have some similar lights that you could use…

view full answer...

Answer 11

While we may have an option for you, we do not have the exact specs on your Allis grease seal part number 5013 29772. However, with the 1.6" ID and 2.5" OD measurements you provides, that is very close to our #58846. This particular grease…

view full answer...

Answer 12

Unfortunately there are no plug-in adapters or harnesses that would allow you to replace the factory 4-way flat trailer connector with a 7-way or a 7-way and 4-way connector on your 2005 Ford F-150. To complete the installation for a brake controller…

view full answer...

Sub and Amp Combo to Use with RV Stereo

Products Referenced in This Question

Featured Help Information

Instructions

Continue Researching