Will the Solera Replacement 21' Awning Fabric fit my Dometic 21" Roller Assembly

Question

Question:

Dometic 9100 21foot awning

asked by: Shane W

0

Expert Reply:

Yes the Solera Replacement Awning Fabric for 21' Roller Assemblies part # LCV000334448 is exactly what you will need to replace your current awning fabric.

I've attached a video of the entire replacement process for you to check out that my buddy Shane did.

expert reply by: Randy B

0

Answer 1

The Lippert Replacement Awning Fabric #LCV000334448 referenced in your question is indeed compatible with Dometic A&E awnings like what you have on your Cedar Creek camper. This fits 21 foot roller assemblies and has a solid black color.

view full answer...

Answer 2

Yes, when you roll the Solera Replacement Awning Fabric #LCV000334448 all the way out there will be a rail/channel on the roller that allows the LCI LED light strip #LC674283 to install.

view full answer...

Answer 3

To get power to the controller of your Solera Smart Arm 12V Power RV Awning part #LC759404, you need to tap into an existing circuit, or run a power wire from the battery with an inline fuse holder, and a 15 amp fuse, like part #SWC9538, and part…

view full answer...

Answer 4

I attached a wiring diagram for the Solera Power Awning Switch Kit #LC285500 for you to check out.

view full answer...

Answer 5

To replace the solid black fabric on your 20' Solera XL awning you need the Replacement Roller and Fabric Kit for 21' Solera XL Power RV Awnings #LC68BR. I checked in with Lippert and it looks like they only offer just the fabric for the…

view full answer...

Answer 6

If you are installing just the Firestone Ride-Rite kit, #F2400, and not also adding an on-board air compressor such as #F2158, then I would estimate that it should take about 2 hours to install the kit. That is for someone with some mechanical…

view full answer...

Answer 7

When installing/adjusting the Solera RV Slide-Out Awning #LCV000163285 tension is applied by rotating the awning roller 14 times. This should apply the needed spring tension so that the fabric doesn't billow in the wind or leave enough slack that…

view full answer...

Answer 8

I've never heard of an actual third brake light connector on a camper shell to plug in on a truck and we don't carry any parts to do that. The light generally needs to be hardwired into the truck's brake light circuit. The issue with this…

view full answer...

Answer 9

If your current springs have 5 leaves then going to a 7 leaf spring will increase the height of the trailer a little and make the trailer more susceptible to sway. Regarding capacity if you go with springs rated higher than what is required it will…

view full answer...

Answer 10

For a standard replacement equalizer for your Dexter 13-122 equalizers you'd want the #TREQE1 or for a cushioned version you'd want the part #K71-653-00 which comes with new shackles and bolts. For a kit that includes new bolts, bushings, and…

view full answer...

Answer 11

Yes, the Solera Slide Topper part #LCV000168106 is the correct fit for your flange width of 90-1/2 inches. This specific model has a box width range of 86 to 91-3/4 inches which is perfect for your width listed.

view full answer...

Answer 12

Since you have a wheelbase/axle spacing of 38 inches the correct hanger kit for slipper springs would be the part #HAP-105-205-01. And then for a 7k trailer axle the u-bolt kit you'd want would be the part #APUBR-8. I attached the diagram to use…

view full answer...

Will the Solera Replacement 21' Awning Fabric fit my Dometic 21" Roller Assembly

Product Page this Question was Asked From

Featured Help Information

Instructions

Miscellaneous Media

Continue Researching