TireMinder i10 TPMS Sensors to Use with Aluminum Valve Stems

Question

Question:

Where are the al valve cap monitors to order for my toad with al. Tire press stems

asked by: E. S

0

Expert Reply:

For aluminum sensors to use with the TireMinder i10 TPMS for RVs # TM56FR the part # TM-2ALUM would be what you'd need for a pair of these sensors. These are needed for if your valve stems are aluminum like it sounds like they are.

expert reply by: Jameson C

0

Answer 1

I spoke with my contact over at Truck Systems about the TPMS for RVs #TST-507-RV-6-C and those TPMS sensors will work for your RV, but he mentioned that you would likely want to use the system that has the Flow-Through caps instead, which can be…

view full answer...

Answer 2

I would be happy to help! The correct system will be dependent on the material of the valve stem, not the wheel it itself. If you have aluminum valve stems I recommend using the TireMinder i10 TPMS for RVs and Trailers w/ Signal Booster - 4 Tire…

view full answer...

Answer 3

The TireMinder i10 TPMS for RVs - LCD Monitor - Signal Booster - 10 External Tire Sensors #TM56FR only comes with the 10 sensors for brass valve cores, but I do have a way that you can get exactly what you're needing. What you can do is get the…

view full answer...

Answer 4

No, the TireMinder A1AS TPMS for RVs and Trailers w/ Signal Booster #TM79FR uses Bluetooth to connect the tire sensors to your smart phone. This will allow for your smartphone to still be able to give you alerts without phone service. We do have…

view full answer...

Answer 5

The TireMinder A1AS TPMS for RVs and Trailers part #TM79FR is what I recommend for a flat-tow setup. It comes with sensors for the towed vehicle and towing vehicle. If the towing vehicles has a dually axle you will be covered but if not you'll…

view full answer...

Answer 6

This is a good question, and it's going to vary between RVs and towed vehicles, so I'll try to break this down. The short version of this is that for your setup you'll want to use brass transmitters. Towed vehicles will have either rubber…

view full answer...

Answer 7

The sensor type needed for your motorhome and trailer is going to depend on the type of valve stems you have. If you have a rubber valve stem, you will need brass transmitters. If you have a metal valve stem, you will need aluminum transmitters. The…

view full answer...

Answer 8

Hey David, from previous customers of ours who have the same 2020 Keystone Raptor 424 we have determined that your pin box style is the Lippert 1621 which means for a Gen-Y gooseneck adapter you'd want the #GY58GR that you referenced.

view full answer...

Answer 9

The manual lockout on your Atwood 85778 surge brake coupler is there so that you can back up the trailer without the brakes locking up on you. Yes you can safely tow your trailer with the broken manual lockout, you just have to make sure you…

view full answer...

Answer 10

I agree it is the right time to upgrade to a Lithium charger/converter as not all are Lithium compatible. I recommend using the Progressive Dynamics Mighty Mini AC/DC Panel and Converter/Smart Charger - 60 Amp #PD4060K which is a replacement for your…

view full answer...

Answer 11

The correct replacement for a Demco Master Cylinder 05680-C is the Replacement Master Cylinder part #5650. I spoke with Demco to confirm this for you.

view full answer...

Answer 12

I did some checking and the hub/drum we offer that will work for you is the part #8-430-5UC3. This uses the same bearings as the 8-415 and will be an exact fit aside from the fact this is a non-ABS setup and the 8-415 came in an ABS setup and non-ABS…

view full answer...

TireMinder i10 TPMS Sensors to Use with Aluminum Valve Stems

Products Referenced in This Question

Product Page this Question was Asked From

Continue Researching