Rivet Size Needed To Install UWS Replacement Locking Paddle Handle # UWSLOCKING

Question

Question:

What size revits does this require?

asked by: James G

0

Expert Reply:

The UWS Replacement Locking Paddle, part # UWSLOCKING would use a 3/16 diameter pop rivet.

expert reply by: Mike L

0

Answer 1

Best way is to drill a hole through the floor of the tool box and then through the bed of the truck and then run a bolt through both. This is the best way to secure a tool box.

view full answer...

Answer 2

The Replacement Locking Paddle Handle for UWS Toolboxes, #UWSLOCKING, doesn't come keyed alike. However, you can (have them keyed)KEY THEM the same by ordering Replacement Lock Cylinder for UWS Toolboxes for Square Paddle Handles - CH502,…

view full answer...

Answer 3

All of the replacement locking cylinders we have for the UWS toolboxes have the same dimensions and catch arm length. The cores are keyed differently but other than this feature they are virtually identical. The only thing I can think of as to why…

view full answer...

Answer 4

I've never heard of an actual third brake light connector on a camper shell to plug in on a truck and we don't carry any parts to do that. The light generally needs to be hardwired into the truck's brake light circuit. The issue with this…

view full answer...

Answer 5

I did some checking and the hub/drum we offer that will work for you is the part #8-430-5UC3. This uses the same bearings as the 8-415 and will be an exact fit aside from the fact this is a non-ABS setup and the 8-415 came in an ABS setup and non-ABS…

view full answer...

Answer 6

Since you have a wheelbase/axle spacing of 38 inches the correct hanger kit for slipper springs would be the part #HAP-105-205-01. And then for a 7k trailer axle the u-bolt kit you'd want would be the part #APUBR-8. I attached the diagram to use…

view full answer...

Answer 7

If you are needing the hub and drum assembly then you will want to go with the Dexter Trailer Hub and Drum Assembly #8-201-5UC3-EZ but if you are just looking for an idler hub then you will want part #8-213-5UC1 instead. These come with the correct…

view full answer...

Answer 8

The old version of the #HBA-CAM used 4 wires, but the product was updated awhile back and now uses only two wires as shown in the photo on the product description page. The white wire from the HBA-CAM would tap into the white ground wire and the blue…

view full answer...

Answer 9

To see all of the correct wheel and tire combos you'd need check out the link I attached. The option I would recommend is the part #TA43RR which is a Load Range C tire size ST175/80R13 mounted on a white spoke wheel with a bolt pattern of 5 on…

view full answer...

Answer 10

The number you provided, "7753400" is a patent number which corelates to the Equalizer for E-Z Flex Suspension part #013-144-03. This is for a single equalizer but if you need the entire kit it's the Dexter E-Z Flex Suspension Kit part…

view full answer...

Answer 11

I have a solution for you, but we do not carry Glo-Brite lights, so replacing it with the same brand will not be something I can offer you. Instead, to replace your Glo-Brite 9852-88, I recommend using the Optronics LED Trailer Tail Light #STL72RB.…

view full answer...

Answer 12

The 40 amp fuse for your 2006 Chevrolet Silverado tow package is used for the 12 volt battery charge circuit. This fuse is located toward the front of the underhood fuse box closest to the front auxiliary positive post (see photo). There may be a…

view full answer...

Rivet Size Needed To Install UWS Replacement Locking Paddle Handle # UWSLOCKING

Product Page this Question was Asked From

Continue Researching