Will 9 inch Long Winch Handle Fit 1998 Fulton T1200 Winch

Question

Question:

Does the 9 inch winch handle fit the Fulton t1200 model winch I bought in 1998

asked by: Joe R

1

Helpful Expert Reply:

Yes, the 9" Long Replacement Handle for Fulton Hand Winches # F501109 is a fit for your T1200 model winch. I reached out to my contact at Fulton who said they haven't changed the handle design for their winches in years so this is compatible.

expert reply by: Jon G

1

Answer 1

I went out to the warehouse to measure the distance between the mounting holes on the Fulton Fulton Single Speed Trailer Winch #F142306 and found the distance between the center hole and left hole to be 3/8". The holes on the Fulton are…

view full answer...

Answer 2

The hole in the handle is slotted, and is meant to replace the handle on a Dutton-Lainson DL1400 or DL1402 winch. The proper replacement for your Fulton T1801 winch would be the Fulton Replacement Winch Handle, part #F501109 or #F501110 depending on…

view full answer...

Answer 3

Essentially to calculate mechanical advantage, first take the output force and then divide it by the input force. Input force is how much force you apply to the handle. Output force is how much force is applied to the load. Some of the winches are…

view full answer...

Answer 4

I would be happy to help you set up your 2022 Toyota Highlander to haul your new travel trailer. The wiring harness you currently have controls your trailer's lighting functions only. You do not need to rewire your Toyota you just need another…

view full answer...

Answer 5

If you are needing the hub and drum assembly then you will want to go with the Dexter Trailer Hub and Drum Assembly #8-201-5UC3-EZ but if you are just looking for an idler hub then you will want part #8-213-5UC1 instead. These come with the correct…

view full answer...

Answer 6

Since you have a wheelbase/axle spacing of 38 inches the correct hanger kit for slipper springs would be the part #HAP-105-205-01. And then for a 7k trailer axle the u-bolt kit you'd want would be the part #APUBR-8. I attached the diagram to use…

view full answer...

Answer 7

I've never heard of an actual third brake light connector on a camper shell to plug in on a truck and we don't carry any parts to do that. The light generally needs to be hardwired into the truck's brake light circuit. The issue with this…

view full answer...

Answer 8

I have a solution for you, but we do not carry Glo-Brite lights, so replacing it with the same brand will not be something I can offer you. Instead, to replace your Glo-Brite 9852-88, I recommend using the Optronics LED Trailer Tail Light #STL72RB.…

view full answer...

Answer 9

If the trailer wheels scrubbed (dragged and scrapped the ground instead of rolling) when jack knifed then it could have thrown something out of alignment or damaged something. First, inspect the suspension. Look for any elongated holes where…

view full answer...

Answer 10

I did some checking and the hub/drum we offer that will work for you is the part #8-430-5UC3. This uses the same bearings as the 8-415 and will be an exact fit aside from the fact this is a non-ABS setup and the 8-415 came in an ABS setup and non-ABS…

view full answer...

Answer 11

The manual lockout on your Atwood 85778 surge brake coupler is there so that you can back up the trailer without the brakes locking up on you. Yes you can safely tow your trailer with the broken manual lockout, you just have to make sure you…

view full answer...

Answer 12

If your vehicle has a factory brake controller plug, you can simply use the Tekonsha Plug-In Wiring Adapter for Electric Brake Controllers – Ford, Item #3034-P, which will connect to the vehicle plug and the brake controller. On the new E-450…

view full answer...

Will 9 inch Long Winch Handle Fit 1998 Fulton T1200 Winch

Product Page this Question was Asked From

Featured Help Information

Miscellaneous Media

Continue Researching