What is Best Way to Have Trailer Spindles Installed on Axle

Question

Question:

Im building my own off road trailer being pulled by a utv. I think these spindles will be good. What is the best way to mount these spindles? Can they be drilled through to put a bolt through?

asked by: Christopher S

0

Expert Reply:

Spindles like # TRU94FR need to be installed by a welder/fabricator with the correct equipment for the job. It's a precision install that requires specials jigs so that the wheel alignment is perfect. Contact local welders to you and ask if they can install axle spindles. If they can't they'll definitely know someone who can.

expert reply by: Jameson C

0

Answer 1

Assuming your tires are in good shape without any bulges the easiest way to determine if you have a bent spindle is to take a straight edge that is longer than the tire and lay it across the tire parallel with your trailer frame and then measure the…

view full answer...

Answer 2

For a replacement of the NOK AB1990E grease seal you'll need the Grease Seal #13194.

view full answer...

Answer 3

Yes the bearing kit part #DL21792 is the correct kit for your trailer hub BT-100. This comes with two bearings L44643 like we know fit that hub part number.

view full answer...

Answer 4

You can verify that the 10-19 grease seal included in Bearing Kit #BK2-100 is the correct one for your spindles by taking two measurements. First you want to measure the rear hub bore where the seal is inserted. The seal's outer diameter needs to…

view full answer...

Answer 5

We can help you find the seal you need, but the part number you mentioned does not match anything we offer. Can you get me the inner and outer diameters of the seal? With that I can see what we have that matches.

view full answer...

Answer 6

If your current springs have 5 leaves then going to a 7 leaf spring will increase the height of the trailer a little and make the trailer more susceptible to sway. Regarding capacity if you go with springs rated higher than what is required it will…

view full answer...

Answer 7

I did some checking and the hub/drum we offer that will work for you is the part #8-430-5UC3. This uses the same bearings as the 8-415 and will be an exact fit aside from the fact this is a non-ABS setup and the 8-415 came in an ABS setup and non-ABS…

view full answer...

Answer 8

You will need the Red LED Trailer Clearance or Side Marker Light #328-K-52 or Amber LED Trailer Clearance or Side Marker Light #328-K-51 for your 2018 Forest River Sunseeker motorhome. These lenses have the same Top Command SAE-AP2-16 markings on the…

view full answer...

Answer 9

I would love to help you upgrade the suspension on your Twilight 2800 travel trailer. The MORryde Rubber Equalizers for Tandem Axle Trailers #MR87ZR that you referenced are a great solution but we do need to double check a few things. First is that…

view full answer...

Answer 10

I've never heard of an actual third brake light connector on a camper shell to plug in on a truck and we don't carry any parts to do that. The light generally needs to be hardwired into the truck's brake light circuit. The issue with this…

view full answer...

Answer 11

Since Demco uses 3,500 drum brake assemblies part #DMSB24429M and #DMSB24428M what you'd need is similar 3,500 electric brake assemblies like the etrailer part #AKEBRK-35L-SA for the left hand side and #AKEBRK-35R-SA for the right hand side. To…

view full answer...

Answer 12

The 40 amp fuse for your 2006 Chevrolet Silverado tow package is used for the 12 volt battery charge circuit. This fuse is located toward the front of the underhood fuse box closest to the front auxiliary positive post (see photo). There may be a…

view full answer...

What is Best Way to Have Trailer Spindles Installed on Axle

Product Page this Question was Asked From

Continue Researching