Mounting kit for a Pro Series 15k 5th Wheel on my 2002 Dodge Ram 2500

Question

Question:

I have a 02 dodge 2500 diesel pick up with 8foot bed. I need a mounting kit for this hitch to my truck?

asked by: J D

0

Expert Reply:

I have a couple options for you that will work for you. The B&W Universal Base Rails and Installation Kit for 5th Wheel Trailer Hitches - 10 Bolt part # BWRVR3200 that you ha looked at would be a great one to use or the Reese Universal Base Rails and Installation Kit for 5th Wheel Trailer Hitches - 10 Bolt part # RP30035 is also a good choice. They will both install the same way the only real difference is in the color. To best match your fifth wheel head the Reese is the best choice.

For a handy wiring connector in the bed of your truck use the Curt 5th Wheel/Gooseneck Wiring Harness 7-Pole part # C56000 this will plug in line between the factory wiring on the rear of the Ram and allow you to have an in bed connector so your wiring isn't hanging over the tailgate.

I've linked the product pages for you and also the videos we have done here to help you out.

expert reply by: Randy B

0

Answer 1

I have a solution for you, it sounds like you have the 5th wheel hitch and the actual rails the hitch attaches too but are needing the custom mounting hardware for your 1999 Dodge Ram Pickup. You are going to better off getting a new set of…

view full answer...

Answer 2

Actually, B & W Hitch offer a reasonably priced 5th wheel bracket/rail kit that works with industry standard rail compatible hitches like your Husky. I'd recommend the #BWRVR3200 install kit. The bed rails are compatible with hitches…

view full answer...

Answer 3

The Curt Universal Fifth Wheel Base Rails with Installation Kit, #C16200 & the B&W Installation Kit, #BWRVR3200 each serve the same purpose but are from different manufacturers. These are both ISR base rails and any hitch made in recent years…

view full answer...

Answer 4

For your 1999 Dodge Ram 2500 long bed there are only universal fifth wheel rail kits available that would require drilling into the truck frame like the B and W part #BWRVR3200. This is by far the best deal though so it would be way to go.

view full answer...

Answer 5

I've never heard of an actual third brake light connector on a camper shell to plug in on a truck and we don't carry any parts to do that. The light generally needs to be hardwired into the truck's brake light circuit. The issue with this…

view full answer...

Answer 6

I did some checking and the hub/drum we offer that will work for you is the part #8-430-5UC3. This uses the same bearings as the 8-415 and will be an exact fit aside from the fact this is a non-ABS setup and the 8-415 came in an ABS setup and non-ABS…

view full answer...

Answer 7

You will have to go with a sliding hitch to allow the trailer to make tight turns. For a trailer 8 feet wide the only bed length that's going to allow 90 degree turns without a slider is a stationary hitch. That being said you have two options.…

view full answer...

Answer 8

The old version of the #HBA-CAM used 4 wires, but the product was updated awhile back and now uses only two wires as shown in the photo on the product description page. The white wire from the HBA-CAM would tap into the white ground wire and the blue…

view full answer...

Answer 9

If you are needing the hub and drum assembly then you will want to go with the Dexter Trailer Hub and Drum Assembly #8-201-5UC3-EZ but if you are just looking for an idler hub then you will want part #8-213-5UC1 instead. These come with the correct…

view full answer...

Answer 10

You will need the Red LED Trailer Clearance or Side Marker Light #328-K-52 or Amber LED Trailer Clearance or Side Marker Light #328-K-51 for your 2018 Forest River Sunseeker motorhome. These lenses have the same Top Command SAE-AP2-16 markings on the…

view full answer...

Answer 11

On a 2005 Chevy Silverado 1500, If you are facing the front of the truck looking at the power distribution box, there will be a post at the back left side and a fuse slot near it. It is that fuse slot that you will install a 30 amp fuse. I have…

view full answer...

Answer 12

The 40 amp fuse for your 2006 Chevrolet Silverado tow package is used for the 12 volt battery charge circuit. This fuse is located toward the front of the underhood fuse box closest to the front auxiliary positive post (see photo). There may be a…

view full answer...

Mounting kit for a Pro Series 15k 5th Wheel on my 2002 Dodge Ram 2500

Products Referenced in This Question

Product Page this Question was Asked From

Featured Help Information

Instructions

Miscellaneous Media

Continue Researching