Replacement Lid For Ventline Metal Ventadome Trailer Vent

Question

Question:

The vent cover is for an enclosed trailer. The white vent cover crumbled and blew off in the storm. It has “DTS MFG Wilsonville, OR AS-13M DOT 452” on the side. The hinge appears to be continuous and it measured +/- 15” x 15” Attached are photos of the writing on the cover, the outside of the vent showing the hinge, and a picture inside showing the hand crank. Since it is for an enclosed cargo trailer, I’d prefer a white replacement to let light in. Which replacement cover do you recommend? Many of your products have 14” x 14” in the description, but the photos show them with a 15” measurement, but I want to be sure to order the correct replacement. Thanks

asked by: Shad S

0

Expert Reply:

Yes your hinge is a metal continuous hinge. Most trailer roof vents are 14-1/4" wide x 14-1/4" long. Looking at your photos it looks like you had a Ventline metal Ventadome Trailer Roof Vent like part # V2092SP-29. I recommend to use the Ventline Ventadome Trailer Roof Vent Cover part # BVD0449-A01 to replace your cover.

expert reply by: Heather A

0

Answer 1

While we do not currently carry the Pacific Dualies 18090 valve stem extenders that you mentioned, I did some research and found that the manufacturer does state that they don't recommend them for use with rubber valve stems. From what I could…

view full answer...

Answer 2

Replacement vent cover #CAM40148 should be correct since it fits Elixir vents made after 1994. Take a look at the video I have linked on this cover. Make sure the hinge style matches your old covers.

view full answer...

Answer 3

I've never heard of an actual third brake light connector on a camper shell to plug in on a truck and we don't carry any parts to do that. The light generally needs to be hardwired into the truck's brake light circuit. The issue with this…

view full answer...

Answer 4

I did some checking and the hub/drum we offer that will work for you is the part #8-430-5UC3. This uses the same bearings as the 8-415 and will be an exact fit aside from the fact this is a non-ABS setup and the 8-415 came in an ABS setup and non-ABS…

view full answer...

Answer 5

If you are needing the hub and drum assembly then you will want to go with the Dexter Trailer Hub and Drum Assembly #8-201-5UC3-EZ but if you are just looking for an idler hub then you will want part #8-213-5UC1 instead. These come with the correct…

view full answer...

Answer 6

If the trailer wheels scrubbed (dragged and scrapped the ground instead of rolling) when jack knifed then it could have thrown something out of alignment or damaged something. First, inspect the suspension. Look for any elongated holes where…

view full answer...

Answer 7

I would be happy to help you set up your 2022 Toyota Highlander to haul your new travel trailer. The wiring harness you currently have controls your trailer's lighting functions only. You do not need to rewire your Toyota you just need another…

view full answer...

Answer 8

Since you have a wheelbase/axle spacing of 38 inches the correct hanger kit for slipper springs would be the part #HAP-105-205-01. And then for a 7k trailer axle the u-bolt kit you'd want would be the part #APUBR-8. I attached the diagram to use…

view full answer...

Answer 9

Since Demco uses 3,500 drum brake assemblies part #DMSB24429M and #DMSB24428M what you'd need is similar 3,500 electric brake assemblies like the etrailer part #AKEBRK-35L-SA for the left hand side and #AKEBRK-35R-SA for the right hand side. To…

view full answer...

Answer 10

The manual lockout on your Atwood 85778 surge brake coupler is there so that you can back up the trailer without the brakes locking up on you. Yes you can safely tow your trailer with the broken manual lockout, you just have to make sure you…

view full answer...

Answer 11

When installing/adjusting the Solera RV Slide-Out Awning #LCV000163285 tension is applied by rotating the awning roller 14 times. This should apply the needed spring tension so that the fabric doesn't billow in the wind or leave enough slack that…

view full answer...

Answer 12

I have a solution for you, but we do not carry Glo-Brite lights, so replacing it with the same brand will not be something I can offer you. Instead, to replace your Glo-Brite 9852-88, I recommend using the Optronics LED Trailer Tail Light #STL72RB.…

view full answer...

Replacement Lid For Ventline Metal Ventadome Trailer Vent

Products Referenced in This Question

Product Page this Question was Asked From

Continue Researching