Replacement Drive Shafts For Venture Landing Gear On Keystone Laredo

Question

Question:

Hello, I need the drive shaft piece that connects the venture gearbox to the cross shaft bar of my landing gear. What is the part number for that connecting piece? I have a 2006 keystone Laredo fifth wheel.

asked by: Martin G

0

Expert Reply:

To replace just the drive shaft you will need part # LC146059 for the lead leg and part # LC146060 for the follow leg on your Venture landing gear.

expert reply by: Heather A

0

Answer 1

We absolutely carry replacement gears like the Lippert Venture Follow Leg Repair Kit for 5th Wheel RV Landing Gear #LC146060 which will work with Lippert Components powered landing gears, which is the most common landing gear used however…

view full answer...

Answer 2

I sent your picture to my tech contact at Lippert and they responded with saying that the mounting brackets are designed to go behind and under the cross shaft of the slide out. If you check out the picture I attached you'll see how it would…

view full answer...

Answer 3

I have an answer for you. Unfortunately, we do not sell replacement components you need as a complete set. They have to be purchased individually. Although, we do carry all those parts. Here are the replacements you need: - Replacement Heavy-Duty…

view full answer...

Answer 4

Yes, the Replacement Heavy-Duty Landing Gear Jack Leg #LC241844 will replace a rear leg for your Lippert 2.0 electric leveling system.

view full answer...

Answer 5

The landing gear looks like a standard set based on the pictures and the dimensions you listed. The part #LC146060 would be what you need for the follow leg and then part #LC146059 for the lead leg.

view full answer...

Answer 6

Thank you for the photo of your trailer landing gear interior. We can help you with a repair kit for the lead and follower legs of your Venture landing gear. For a lead leg repair kit use #LC146059 and for the follow leg use kit #LC146060. It is…

view full answer...

Answer 7

I've never heard of an actual third brake light connector on a camper shell to plug in on a truck and we don't carry any parts to do that. The light generally needs to be hardwired into the truck's brake light circuit. The…

view full answer...

Answer 8

I did some checking and the hub/drum we offer that will work for you is the part #8-430-5UC3. This uses the same bearings as the 8-415 and will be an exact fit aside from the fact this is a non-ABS setup and the 8-415 came in an ABS setup and…

view full answer...

Answer 9

Since Demco uses 3,500 drum brake assemblies part #DMSB24429M and #DMSB24428M what you'd need is similar 3,500 electric brake assemblies like the etrailer part #AKEBRK-35L-SA for the left hand side and #AKEBRK-35R-SA for the right hand side. To…

view full answer...

Answer 10

I would love to help you upgrade the suspension on your Twilight 2800 travel trailer. The MORryde Rubber Equalizers for Tandem Axle Trailers #MR87ZR that you referenced are a great solution but we do need to double check a few things. First is that…

view full answer...

Answer 11

You will need the Red LED Trailer Clearance or Side Marker Light #328-K-52 or Amber LED Trailer Clearance or Side Marker Light #328-K-51 for your 2018 Forest River Sunseeker motorhome. These lenses have the same Top Command SAE-AP2-16 markings on the…

view full answer...

Answer 12

If your current springs have 5 leaves then going to a 7 leaf spring will increase the height of the trailer a little and make the trailer more susceptible to sway. Regarding capacity if you go with springs rated higher than what is required it will…

view full answer...

Replacement Drive Shafts For Venture Landing Gear On Keystone Laredo

Products Referenced in This Question

Product Page this Question was Asked From

Continue Researching