Replacement Mounting Brackets for Westin HDX Grille Guard On a 03-07 Chevy Silverado 1500

Question

Question:

Will the #57-117PK fit my 2003 Silverado 1500 LS?

asked by: David P

0

Expert Reply:

The Replacement Hardware Kit part # 57-117PK is designed for the Westin HDX Grille Guard with Punch Plate part # 57-1175. The Westin HDX Grille Guard with Punch Plate fits the following:

2003 - 2006 Chevrolet Silverado 1500 LD (Light Duty - 6 Lug)
2007 - 2007 Chevrolet Silverado Classic 1500 LD (Light Duty - 6 Lug)

Therefore, if you have the above grille guard and one of the above vehicles then the replacement hardware kit will work. Please note, the trim level such as LT or LS does not affect fit.

expert reply by: Conner L

0

Answer 1

Thank you for purchasing from etrailer! You did a great job selecting compatible parts. When using Leaf Springs #e64SR with the #AP233 Equalizer Kit and the #H248 Hanger Kit, there should be 29-1/2" between the front and center hangers and…

view full answer...

Answer 2

Installing the Union Tee #AL21838 with your #AL57575 will tie the pressure of the two air bags together. So yes, a shift in a very heavy load like a truck camper will potentially result in air being forced from one into the other. The reason I say…

view full answer...

Answer 3

On single axle trailers typically you put the hanger spacing right at 1/4 of an inch shorter than the leaf spring length from eye to eye center. So if you were using the leaf spring part #e54SR that you referenced which measures 25-1/8 inches long…

view full answer...

Answer 4

An oil seal like Redline part #9103309 installs in the back side of the hub (the side nearest the trailer's frame) with the sides or "legs" of the seal inserted into the hub's bore. This means that the flat metal surface of the seal…

view full answer...

Answer 5

I think the best way to explain how to install a grease seal like #10-9 is to take a look at the video I have linked. Go to about the 6 minute, 10 second mark. At this point in the video, our installer begins to install the seal in the back of the…

view full answer...

Answer 6

A drop axle certainly can make it tough to reach the star wheel adjuster on a drum brake. The adjuster spoon tool we offer #W80630 has a 90-degree bend that will often let you get access to the adjuster even on a drop axle. Essentially you will need…

view full answer...

Answer 7

The Gooseneck to 5th Wheel Trailer Coupler Adapter #KPG5-R30IP you found is our only 4" tube rated for 30K. The plate does not have to sit perfectly square inside the 5th wheel hitch as it will still latch into the coupler. You will want to face…

view full answer...

Answer 8

I spoke to my contact at Horizon Global. He said it is acceptable to mount the Bulldog Powered-Drive Kit #BD1824200100 to the slave jack itself. He also said that if you need to switch the motor wires to make it work correctly, that would be fine, as…

view full answer...

Answer 9

Sometimes just use of new spring bars can update a weight distribution hitch to match the tongue weight (TW) of a new trailer, but in the case of your Equal-I-zer system, part #EQ37140ET, the highest-rated bars are the 1400-lb set #EQ90-01-1499 that…

view full answer...

Answer 10

The trick here is to get as close as possible. If you are talking about less than 2 inches or so, there is nothing to worry about. Having the trailer tongue a bit too high is preferable to it being too low. You may be a good candidate for an…

view full answer...

Answer 11

The Americana Aluminum 7-Star Spoke Trailer Wheel you referenced, #AM22654 as well as the rest of the 15 x 6, 6 lug alloy wheels we offer all have a 2830 lb weight capacity. This would be more than enough capacity for your 10000 lb capacity trailer.…

view full answer...

Answer 12

I did some checking and basically the cutout bumper is the regular factory bumper. The Curt hitch, #C15312, will fit up tighter and a little more recessed, apparently the same way the factory hitch does if it were installed. Some people like the…

view full answer...

Replacement Mounting Brackets for Westin HDX Grille Guard On a 03-07 Chevy Silverado 1500

Products Referenced in This Question

Product Page this Question was Asked From

Featured Help Information

Instructions

Continue Researching