Can Rhino-Rack Ski and Fishing Rod Carrier Fit Inno Aero Shaped Crossbars
Question:
If R572-43159 is put on the end of the Inno Aero bar, it would just hang on the side above the door.. so it shouldnt hit anything. Maybe the door? Whats the measurement of it hanging down from the inno bar so I can measure it. And do I need a separate T-slot screws or the current kit would suffice to mount the R572-43159 Thanks.
asked by: Jess
Expert Reply:
The Rhino-Rack Ski and Fishing Rod Carrier for Pioneer Platform Rack # RR572-43159 is compatible with the top channels of the Inno crossbars part # INXB123-130 that you referenced. That said, your bars might be too low to the roof of your vehicle for the rack to install at an angle. If this is the case you could always clamp the carrier around the crossbars.
Products Referenced in This Question
Inno Aero Crossbars - Aluminum - Black - 48" Long and 51" Long - Qty 2
- Roof Rack
- Crossbars
- Aero Bars
- 48 Inch Bar Space
- 2 Bars
- Overhang
- Black
- Inno
more information >
Product Page this Question was Asked From
Rhino-Rack Ski and Fishing Rod Carrier for Pioneer Platform Rack - Locking - 2 Skis or 4 Rods
- Fishing Rod Holders
- Vehicle Rod Carriers
- Roof Mount
- Aluminum
- 4 Rods
- Black
- Rhino Rack
more information >
Featured Help Information
Instructions
Continue Researching
- Shop: Rhino-Rack Ski and Fishing Rod Carrier for Pioneer Platform Rack - Locking - 2 Skis or 4 Rods
- Shop: Rhino-Rack Fishing Rod Carrier - Locking - 8 Fishing Rods
- Q&A: Will The Rhino-Rack Ski And Fishing Rod Carrier For Platform Rack Fit Putco T-Slot Rails
- Shop: Rhino-Rack Ski and Fishing Rod Carrier Brackets for Pioneer Platform Rack
- Video: Rhino Rack Vehicle Fishing Rod Racks - Roof Rack - RR572-43159 Review
- Shop: Front Mount Hitch
- Shop: Curt Front Mount Trailer Hitch Receiver - Custom Fit - 2"
- Shop: Rhino-Rack Fishing Rod Carrier - Locking - 11 Fishing Rods
- Search Results: 44649
- Shop: Dust Cap for Kodiak Disc Brake Kit
- Video: Choosing the Right Trailer Wiring
- Shop: Trailer Hitch
- Q&A: Wiring a Camper Shell Third Brake Light on a 2017 Chevrolet Silverado
- Article: How to Choose the Right Trailer Hitch Class
- Shop: Cam-Action Lockable Door Latch w/ 36" Pipe for Enclosed Trailers - Zinc Plated Steel
- Search Results: 68149
- Shop: Trailer Wiring
- Q&A: 10k Dexter Replacement Hub for a 8-415
- Article: Trailer Wiring Diagrams
- Video: Choosing the Right Brake Controller
- Video: Trailer Hitch Installation - 2011 Toyota Yaris
- Shop: Brake Controller
- Search Results: 25580
- Article: Brake Controller 7- and 4-Way Installation Kit (ETBC7)
- Q&A: Replacement Hub Needed for Lippert 122093 Hub on 5,200 lbs Axle
- Q&A: Replacement LED Top Command Clearance Light With SAE-AP2-16 On Lens For 2018 Sunseeker Motorhome
- Shop: Suspension Enhancement
- Search Results: dust caps
- Article: Trailer Tire Sizing
- Video: Review of SuperSprings Trailer Leaf Spring Suspension - Springs - SS26MV
Jess
1/2/2020
If R572-43159 is put on the end of the Inno Aero bar, it would just hang on the side above the door.. so it shouldnt hit anything. Maybe the door? Whats the measurement of it hanging down from the inno bar so I can measure it. And do I need a separate T-slot screws or the current kit would suffice to mount the R572-43159 Thanks.