How Wide is Ramp Hook of Gen-Y Hitch Aluminum Loading Ramp Set

Question

Question:

I am wondering what is the width between the ramp itself and the hook that goes over the rail of the trailer. I am looking for a ramp that could possibly fit over an inch and a half round bar stock.. Thanks

asked by: Corey M

0

Expert Reply:

The hook opening of the Gen-Y Hitch Aluminum Loading Ramp Set # 325-GH-R72 is two inches wide. I attached a picture that shows where the measurement is taken.

expert reply by: Jameson C

0

click to enlarge

Answer 1

I went out to the warehouse and took a look at the Gen-Y Hitch Aluminum Loading Ramp Set item #325-GH-R72. I have linked a picture below that will show you what the bottom end of this ramp looks like. This ramp set is 72" long x 14"…

view full answer...

Answer 2

The height restriction on ramp set #288-07502 has to do with the distribution of the weight, ability for tires to grip, and clearance between the tops of the ramps and the vehicle rolling up them. The shorter the ramp the more severe the angle will…

view full answer...

Answer 3

You can put a maintenance charge on your trailer battery with the 12 volt accessory circuit of the 7-way. The 1:00 position of your 7-way carries this circuit. You would just need to run a length of 10 gauge wire like part #10-1-1 (sold by the…

view full answer...

Answer 4

I believe you are referring to the 1" prongs on the Stallion Aluminum Car Hauler Ramp Set #288-07503 that are designed to grab onto the small gap at the end of most trailers. This not only provides a secure connection when loading/unloading,…

view full answer...

Answer 5

I do have a solution for you, but the Aluminum Car Hauler Ramp Set #288-07503 that you referenced has a max height of 16" for loading equipment. I did speak with my contact at Gen-Y Hitch who said that their aluminum loading ramps…

view full answer...

Answer 6

Given the information you provided (thanks for that, by the way), the #288-07502 ramps you've asked about would work really well for you. They're designed for a 16 inch maximum loading height, so they'll work perfectly with the 14 inch…

view full answer...

Answer 7

I have a solution for you and you might be able to make the Car Hauler ramps you were looking at work without worry about slippage, but I think we can offer something better. From what I've seen, even if you've got molded wheels on your mower…

view full answer...

Answer 8

For the pair of ramps that come with the #325-GH-R72 the total weight is 61 lbs.

view full answer...

Answer 9

I was able to verify that the weight capacity for the Aluminum Car Hauler Ramp Set #288-07503 that you referenced is indeed 6,000 pounds (not kilograms) for the pair and 3,000 pounds per panel. The recommended maximum height of 16 inches is simply…

view full answer...

Answer 10

The Gen-Y 72" Ramps #325-GH-R72 do have hooks on the end to help make connection to the trailer easier and more stable, but there isn't an additional plate that can be added to a trailer specifically for this application. With that said, you…

view full answer...

Answer 11

I did some checking and the hub/drum we offer that will work for you is the part #8-430-5UC3. This uses the same bearings as the 8-415 and will be an exact fit aside from the fact this is a non-ABS setup and the 8-415 came in an ABS setup and non-ABS…

view full answer...

Answer 12

You will need the Red LED Trailer Clearance or Side Marker Light #328-K-52 or Amber LED Trailer Clearance or Side Marker Light #328-K-51 for your 2018 Forest River Sunseeker motorhome. These lenses have the same Top Command SAE-AP2-16 markings on the…

view full answer...

How Wide is Ramp Hook of Gen-Y Hitch Aluminum Loading Ramp Set

Product Page this Question was Asked From

Featured Help Information

Miscellaneous Media

Continue Researching