Gap Between Frame and Hitch When Installing Draw-Tite Hitch On 2017 Jeep Patriot
Question:
Hi. I am installing a draw tite 75712 on a 2017 jeep patriot. There is a total gap of 5/8 inch between the widest part of the hitch and the inside width between the frame. Is it appropriate to use spacers. I have large diameter 1/8 inch thick washers. Would these be ok or is there somethimg else I should use?
asked by: Thomas C
Expert Reply:
The Draw-Tite Max-Frame Trailer Hitch Receiver part # 75712 is a confirmed fit for a 2017 Jeep Patriot. That said, there should be no washers or spacers needed to fill the gap between the frame and flange on the trailer hitch. If a gap is present, you may want to bend the flanges out on the trailer hitch. The other option as you mentioned is to just run the bolts down as that will then help line-up the flange to the frame rail but you will need to be careful about stressing the frame too much so bending as mentioned above is best. I have attached some other parts you might want to consider if towing a trailer as well.
T-One Vehicle Wiring Harness with 4-Pole Flat Trailer Connector part # 118552 (Plug-N-Play)
Ball Mount Kit for 2" Hitches part # 989900
Products Referenced in This Question
T-One Vehicle Wiring Harness with 4-Pole Flat Trailer Connector
- Custom Fit Vehicle Wiring
- Trailer Hitch Wiring
- Powered Converter
- Custom Fit
- 4 Flat
- Tekonsha
more information >
etrailer Ball Mount Kit for 2" Hitches - 7,500 lbs
- Trailer Hitch Ball Mount
- Fixed Ball Mount
- 1-7/8 Inch Ball
- 2 Inch Ball
- Two Balls
- Steel Ball
- Steel Shank - Gloss Black
- Drop - 2 Inch
- Drop - 4 Inch
- Rise - 1 Inch
- Rise - 3 Inch
- Fits 2 Inch Hitch
- 7500 lbs GTW
- Class III
- Ball Mount Kit
- etrailer
more information >
Product Page this Question was Asked From
Draw-Tite Max-Frame Trailer Hitch Receiver - Custom Fit - Class III - 2"
- Trailer Hitch
- Custom Fit Hitch
- Class III
- 525 lbs TW
- 3500 lbs GTW
- 2 Inch Hitch
- Concealed Cross Tube
- Draw-Tite
more information >
Featured Help Information
Instructions
Continue Researching
- Shop: Trailer Hitch
- Shop: Trailer Wiring
- Search Results: all648544
- Shop: Curt Trailer Hitch Receiver - Custom Fit - Class III - 2"
- Shop: No-Drill Mount Bracket, Long
- Shop: Powerbuilt Trim Pad Remover
- Shop: Curt T-Connector Vehicle Wiring Harness for Factory Tow Package - 4-Pole Flat Trailer Connector
- Shop: No-Drill Mount for Electrical Mounting Bracket - Short
- Shop: Trunk Bike Rack
- Shop: Roof Rack
- Shop: Vehicle Air Mattress
- Shop: Draw-Tite Max-Frame Trailer Hitch Receiver - Custom Fit - Class III - 2"
- Shop: Curt Trailer Hitch Receiver - Custom Fit - Class V Commercial Duty - 2-1/2"
- Video: Curt Trailer Hitch Installation - 2018 Kia Soul
- Q&A: What Universal Class V Hitch Receiver will Fit My 34-Inch Frame?
- Q&A: What is the Difference Between a 4-Way and 7-Way Trailer Connector
- Video: Draw-Tite Max-Frame Trailer Hitch Installation - 2021 Lexus RX 350
- Q&A: Will Curt Trailer Hitch Receiver C73DR Work W/ Lift Gate Sensor On 2021 Lexus RX 350
- Video: B and W Trailer Hitch - Custom Fit Hitch - BWHDRH25211 Review
- Q&A: Will The Trailer Hitch DT73QR Obstruct The Lift Gate Sensor On A 2023 Lexus RX 350?
- Q&A: Where is the Trailer Fuse on a 2021 Lexus RX 350?
- Q&A: Cutting Steps for Installation on the Draw-Tite 75540 Hitch on a 2022 Lexus RX 350
- Q&A: Distance From Frame to Receiver On Curt Trailer Hitch C15312 for Chevy Silverado
- Video: Saris Hitch Bike Racks Review - 2017 Chevrolet Trax
- Article: Trailer Hitch Installation Tips
- Video: How to Make a Thread Tap
- Article: My Trailer Hitch Doesn't Fit
- Video: Trailer Hitch Installation - 2013 Subaru Outback Wagon - Draw-Tite
- Video: Curt Folding Hitch Cargo Carrier Review
- Search Results: receiver hitch