Trailer Hitches that Fit 2020 Subaru Forester

Question

Question:

do you know if the 76271 or C13409 will fit a 2020 Subaru Forester? These are 2 that fit a 2019

asked by: LELAN W

0

Expert Reply:

The Curt hitch part # C13409 has been carried over as a fit for the 2020 Subaru Forester as well as the EcoHitch part # 306-X7391 so realistically the Draw Tite part # 76271 would also carry over although Draw Tite hasn't officially carried it over.

expert reply by: Jameson C

0

Answer 1

The etrailer #e83ZR, Curt #C13409, and Draw-Tite #76271 are all incredibly similar and have the same capacity. In fact, the etrailer hitch and the Curt are exactly the same with the exception of the finish. The etrailer hitch has a matte black powder…

view full answer...

Answer 2

There is only one main difference between the Curt Hitch #C13409 and the Draw-Tite Hitch #76271 for the 2021 Subaru Forester. That difference involves the bumper clearance measurement of the shanks. While the Curt measures 4 inches from the center of…

view full answer...

Answer 3

I suggest the Curt Trailer Hitch Receiver Class III Part #C13409. The reason being, the measurement from the center of the hitch pin hole, to the edge of the bumper has been measured at approximately 4". The measurement with the Draw-Tite option…

view full answer...

Answer 4

For your 2020 Subaru Forester, I recommend the Curt hitch. It is going to be able to handle your Yakima HoldUp EVO 2, part #Y02479, without any problems. Both the Curt and Draw-Tite hitches are Class III hitches with 2" receivers. They both also…

view full answer...

Answer 5

Since the Curt #C13409 has 4" from the hitch pin hole to the farthest edge of the bumper versus the Draw-Tite Hitch #76271 with 5" from the hitch pin hole to the farthest edge of the bumper, Curt will be your better bet. The 20x59 Curt…

view full answer...

Answer 6

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 7

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 8

I've never heard of an actual third brake light connector on a camper shell to plug in on a truck and we don't carry any parts to do that. The light generally needs to be hardwired into the truck's brake light circuit. The issue with this…

view full answer...

Answer 9

The manual lockout on your Atwood 85778 surge brake coupler is there so that you can back up the trailer without the brakes locking up on you. Yes you can safely tow your trailer with the broken manual lockout, you just have to make sure you…

view full answer...

Answer 10

From what I could find it looks like your 122R (red) and 122Y (amber) lights measure 3.75" x 1.70" x .81". We don't have any replacement lense directly for the GLO-BRITE lights but we do have some similar lights that you could use…

view full answer...

Answer 11

If you are needing the hub and drum assembly then you will want to go with the Dexter Trailer Hub and Drum Assembly #8-201-5UC3-EZ but if you are just looking for an idler hub then you will want part #8-213-5UC1 instead. These come with the correct…

view full answer...

Answer 12

I would be happy to help you set up your 2022 Toyota Highlander to haul your new travel trailer. The wiring harness you currently have controls your trailer's lighting functions only. You do not need to rewire your Toyota you just need another…

view full answer...

Trailer Hitches that Fit 2020 Subaru Forester

Products Referenced in This Question

Product Page this Question was Asked From

Featured Help Information

Instructions

Continue Researching