Timbren Rear Suspension Enhancement System TGMRTT15S Height

Question

Question:

How tall are they for the rear of a2000 GMC 1500

asked by: Eldon B

0

Expert Reply:

The Timbren Rear Suspension Enhancement System part # TGMRTT15S for the 2000 GMC Sierra 1500 springs themselves measures 3-1/4" tall. If you use the spacer the spring will be 4-1/4". Timbren does require 1/2" and 1-1/2" between the rubber spring and the contact point when not loaded down.

expert reply by: Heather A

0

Answer 1

The Timbren Rear Suspension Enhancement System #TGMRTT15S for the 2020 Chevrolet Silverado 1500 are very easy to install. I have linked the instructions for them below. To remove the factory bump stop you need a 10mm deep well socket and the Timbren…

view full answer...

Answer 2

The difference between the two Timbren systems you referenced is the application for each. The Timbren Rear Suspension Enhancement System - Severe Duty #TGMRTT15S is designed for service vehicles only so it would not work for you. The #TGMRCK15S…

view full answer...

Answer 3

Since you have a 6 inch suspension lift on your 2015 Ford F-150 a trailer what you will need to use is the Timbren Rear Suspension Enhancement System #TFR1504E. The reason for that is the SumoSprings do not have lift spacers available to make up for…

view full answer...

Answer 4

It is permissible to stack two 1-inch spacers #A25723-90AH00 to give you a total of 2-inches of height adjustment for your Timbren rear axle kit. Rear axle jounce spring kits like those from Timbren are intended primarily for use with supporting…

view full answer...

Answer 5

When installing suspension enhancement on your 2019 Toyota Tundra that a 6 inch lift The RoadActive Suspension #RAS4611TD will work for you as long as the leaf springs are stock, if not The Timbren Rear Suspension Enhancement System #TTORTUN4 will…

view full answer...

Answer 6

To be able to tow a dump trailer at your 2016 Ford F-350's maximum towing capacity of 14,000 pounds, you will need to use a weight distribution system. In Ford's towing guide, they state that the maximum loaded trailer weight requires use of…

view full answer...

Answer 7

The mounting holes on the Curt SecureLatch Pintle Hook #CU97FR are spaced 1-3/4" apart vertically and 3-3/8" horizontally on center. I have an alternate solution with the information you requested as when I spoke to Curt they said this…

view full answer...

Answer 8

In order to choose the best weight distribution hitch, you will first need to know your total tongue weight (TW), which is the tongue weight of your fully loaded and ready to go trailer plus the weight of any cargo behind the rear axle of your tow…

view full answer...

Answer 9

Yes, the Timbren kit part #TFR250SDE that you referenced is a confirmed fit for your 2004 Ford F-250 2wd with stock height suspension. I attached an install video we made that shows this kit installed on a 2004 F-250 just like yours for you to check…

view full answer...

Answer 10

You have many options for a 4 inch lift on your 2001 Ford F-250 4x4 regarding suspension enhancement to reduce sag. For an air spring option, I recommend the Air Lift LoadLifter 5000 Air Helper Springs - Rear Axle #AL57390 along with the Air Lift…

view full answer...

Answer 11

The Timbren #TGMRTT15S is for service vehicles such as tow trucks; they are very stiff and for a standard 2017 Chevy Silverado 1500 truck that is for towing, you definitely don't want to use those. The best Timbrens for your '17 Silverado…

view full answer...

Answer 12

I did some checking and the hub/drum we offer that will work for you is the part #8-430-5UC3. This uses the same bearings as the 8-415 and will be an exact fit aside from the fact this is a non-ABS setup and the 8-415 came in an ABS setup and non-ABS…

view full answer...

Timbren Rear Suspension Enhancement System TGMRTT15S Height

Product Page this Question was Asked From

Featured Help Information

Instructions

Miscellaneous Media

Continue Researching