Trailer Hitch that Fits 2014 Volkswagen Jetta TDI

Question

Question:

Do you make a trailer hitch that will fit a 2014 be Jetta tdi diesel?

asked by: Eric D

1

Helpful Expert Reply:

The only hitch that will fit the 2014 Volkswagen Jetta is the Curt # C11474. However, it will not fit the TDI version. If you let me know what you need a hitch for, I could recommend a trunk mounted bike rack for bikes or a roof rack for cargo. Just let me know what your goals are and I can help.

expert reply by: Jameson C

1

Answer 1

The Curt #C11474 does not fit the 2010 Jetta TDI. Instead, we have the EcoHitch Hidden Trailer Hitch Receiver - Custom Fit - 2" #306-X7284. I attached the installation instructions and an installation video for you to check out.

view full answer...

Answer 2

I have a solution for you but there are no plug and play adapters for your 2014 VW Jetta Sportwagen. For a 4-flat connector you are going to want the Curt Wiring Harness Kit w/ 4-Pole Trailer Connector and Installation Kit item #C59236. This kit…

view full answer...

Answer 3

The Curt hitch part #C11474 that you referenced actually replaced the part number 11072 that you mentioned, but it will not fit the TDI version of the SportWagen. That said the only hitch we have confirmed as a fit for the TDI model of a 2014…

view full answer...

Answer 4

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 5

I've never heard of an actual third brake light connector on a camper shell to plug in on a truck and we don't carry any parts to do that. The light generally needs to be hardwired into the truck's brake light circuit. The issue with this…

view full answer...

Answer 6

I did some checking and the hub/drum we offer that will work for you is the part #8-430-5UC3. This uses the same bearings as the 8-415 and will be an exact fit aside from the fact this is a non-ABS setup and the 8-415 came in an ABS setup and non-ABS…

view full answer...

Answer 7

If you are needing the hub and drum assembly then you will want to go with the Dexter Trailer Hub and Drum Assembly #8-201-5UC3-EZ but if you are just looking for an idler hub then you will want part #8-213-5UC1 instead. These come with the correct…

view full answer...

Answer 8

Since you have a wheelbase/axle spacing of 38 inches the correct hanger kit for slipper springs would be the part #HAP-105-205-01. And then for a 7k trailer axle the u-bolt kit you'd want would be the part #APUBR-8. I attached the diagram to use…

view full answer...

Answer 9

If the trailer wheels scrubbed (dragged and scrapped the ground instead of rolling) when jack knifed then it could have thrown something out of alignment or damaged something. First, inspect the suspension. Look for any elongated holes where…

view full answer...

Answer 10

Since Demco uses 3,500 drum brake assemblies part #DMSB24429M and #DMSB24428M what you'd need is similar 3,500 electric brake assemblies like the etrailer part #AKEBRK-35L-SA for the left hand side and #AKEBRK-35R-SA for the right hand side. To…

view full answer...

Answer 11

When installing/adjusting the Solera RV Slide-Out Awning #LCV000163285 tension is applied by rotating the awning roller 14 times. This should apply the needed spring tension so that the fabric doesn't billow in the wind or leave enough slack that…

view full answer...

Answer 12

I would be happy to help you set up your 2022 Toyota Highlander to haul your new travel trailer. The wiring harness you currently have controls your trailer's lighting functions only. You do not need to rewire your Toyota you just need another…

view full answer...

Trailer Hitch that Fits 2014 Volkswagen Jetta TDI

Product Page this Question was Asked From

Featured Help Information

Instructions

Continue Researching