How to Support Trailer When Replacing Landing Gear Motor

Question

Question:

Does the trailer need to be supported to replace the motor?

asked by: Glen L

1

Helpful Expert Reply:

When replacing your landing gear motor like # LC241795, the trailer can be supported by your landing gear legs. You do not need a second set of jacks or jack stands. With the motor removed, the gear box will not turn to allow the legs to drop.

I have included a video that shows the installation process for a similar landing gear motor.

expert reply by: Carla M

1

Answer 1

In order to add a motor and convert a follow leg on a landing gear system to a lead leg, you would essentially need to replace the inner components on the leg as well, which is a very extensive and potentially expensive process. It will be much…

view full answer...

Answer 2

Yes, the Lippert HD 6500-lbTuson 5th Wheel RV Landing Gear Motor #LC196308 will work as an upgrade replacement with more capacity for your Venture landing gear. This motor works with landing gear systems branded as Lippert, Venture, Stromberg, or…

view full answer...

Answer 3

What you need for your Isuzu NPR truck is a powered converter #C59236. It is compatible with incandescent and LED trailer lights. I have included a link to the installation instructions for you. This harness does require a direct connection to the…

view full answer...

Answer 4

Assuming your Sprinter has the factory tow package with the 7-way at the rear bumper, in addition to the #RED24FR Redarc Tow-Pro Liberty Brake Controller, you'll also need the #3063-P wiring harness and the #331-TPH-017. The connector to install…

view full answer...

Answer 5

A TCM double-lip grease seal number 127194 has an inner diameter of 1.274-inches and an outer diameter of 1.983-inches according to my research. The available grease seal nearest to those dimensions that we offer is part #RG06-010, which is a…

view full answer...

Answer 6

It could be a tow package fuse on the vehicle. Use the owners manual to find the locations of fuses/relays related to the tow package wiring to check them and replace as needed. If the issue is not a fuse or relay then you can test the vehicle side…

view full answer...

Answer 7

I agree it is the right time to upgrade to a Lithium charger/converter as not all are Lithium compatible. I recommend using the Progressive Dynamics Mighty Mini AC/DC Panel and Converter/Smart Charger - 60 Amp #PD4060K which is a replacement for your…

view full answer...

Answer 8

The length of wire desired depends on your vehicle connection and your personal preference. You want enough slack for turning, but not so much for dragging as you mentioned. A little extra slack isn't a problem and not enough could lead to stress…

view full answer...

Answer 9

If your current springs have 5 leaves then going to a 7 leaf spring will increase the height of the trailer a little and make the trailer more susceptible to sway. Regarding capacity if you go with springs rated higher than what is required it will…

view full answer...

Answer 10

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 11

The hub/drum you sent in a picture of is a Lippert 8,000 lb axle hub with an 8 on 6-1/2 inch bolt pattern designed for oil-bath applications. The correct replacement then is the #8-285-10UC3-A.

view full answer...

Answer 12

If your old axles have a 5 bolt brake flange the assemblies like Dexter Electric Trailer Brake Assembly - 12" - Left Hand - 6,000 lbs part #23-105 or Dexter Electric Trailer Brake Assembly - 12" - Right Hand - 6,000 lbs part #23-106 will…

view full answer...

How to Support Trailer When Replacing Landing Gear Motor

Product Page this Question was Asked From

Featured Help Information

Miscellaneous Media

Continue Researching