Replacement 7-Way Recommendation for Intertek on Monaco Motorhome

Question

Question:

Hello, I have a 2008 Beaver motor home made by Monaco and it has an Intertec 7 pin plug socket. I’d like to purchase a direct replacement if possible. Do you have one?

asked by: Chuck J

0

Expert Reply:

Thanks for the picture of the 7-way you have on your Motorhome. While we don't carry the Intertek brand the Pollak 7-way part # PK11893 that you referenced is a direct replacement since thankfully the RV industry uses the same design. So this will plug right into the round connector your current 7-way has and work well.

expert reply by: Jameson C

0

Answer 1

When wiring a trailer connector, it is best to wire by function, as wire colors can vary. We have an excellent wiring diagram on our website, I will provide you a link so you can look at it. If you are looking at the inside of the trailer connector…

view full answer...

Answer 2

In order to flat-tow a thirteenth generation (2015-2018) Ford F-150 with all four wheels on the ground behind a motorhome you are going to need a tow bar, base plate kit, safety cables, tail light wiring harness, supplemental braking system, and…

view full answer...

Answer 3

If I follow correctly, your inside the bed connector is the round 6 way and you want an adapter that plugs into this so you can use a 7-wat RV adapter. We have the Buyers Products 6-Way Round to 7-Way Blade RV Adapter, #337TC1067P.

view full answer...

Answer 4

Since wire color codes are NOT universal, we always recommend wiring by function, rather than wire color. If you look at the Trailer Wiring FAQ article I have linked you to, you can see some diagrams showing the proper way to wire a vehicle and…

view full answer...

Answer 5

I attached a picture that shows the pin out diagram for the Pollak 5th Wheel / Gooseneck T-Connector with 7-Pole #PK11893-11932 that you referenced.

view full answer...

Answer 6

To see a couple diagrams that show how the 6-way to 7-way adapter part #47435 is wired up check out the pictures I attached. The 6-way of this adapter has the center pin as the 12 volt circuit. That is the usual circuit that gets moved around on…

view full answer...

Answer 7

I have added a photo detailing the wiring connections for the Pollack Heavy-Duty, 7-Pole, Round Pin conncetor, #PK11700, see link. This is a SAE J560 compliant connector. The wiring diagram for the vehicle side connector, #PK11720, is pictured…

view full answer...

Answer 8

To cover the easiest things first, make sure that the brake controller output or gain is turned up. If the power is low then the voltage on the blue wire will be low. When testing for voltage make sure to use the manual override and not the brake…

view full answer...

Answer 9

Either one is fine to do. With the Fulton Hi-Mount Spare Tire Carrier part #FSTC1000301 you are not going to be adding a great deal of width to your trailer so the difference is minimum. Giving you my opinion since there is no rule I would Choose…

view full answer...

Answer 10

Yes, if you install the Roadmaster Diode kit part #RM-154 on the circuit that carries the taillight signal to both taillight bulbs both of them will light up while the Blazer is being flat towed. I attached a diagram that shows how the wiring kit…

view full answer...

Answer 11

In order to flat-tow a 2018 Ford F-150 you'll need a few different things such as a base plate kit, tow bar, safety cables, lighting, and braking system to name a few. I have attached a list of all these components below for you to review.…

view full answer...

Answer 12

By all accounts the Curt Spectrum Trailer Brake Controller #C51170 works well and is easy to use and install on most vehicles. It is a brand new item so not a lot of feedback has come in on it. I did learn a few things though after speaking with our…

view full answer...

Replacement 7-Way Recommendation for Intertek on Monaco Motorhome

Product Page this Question was Asked From

Featured Help Information

Miscellaneous Media

Continue Researching