Can the Replacement Cable Lock Assembly for the Yakima HoldUp Bike Carrier be Keyed Alike

Question

Question:

Had had to cut the old ones key broke I just need two of them to replace so can you sell these in a set with the same key? Thanks!

asked by: David H

0

Expert Reply:

The Replacement Cable Lock Assembly # Y8890202 comes to us with the lock cores already packaged together so we can't really determine if the lock cores will match or not. Once you received them if they don't match we do have a wide variety of replacement cores that you can use to make sure they are keyed alike.

expert reply by: Jon G

0

Answer 1

I checked with Yakima and for the Exo Swingbase part #Y34VR the correct replacement hitch pin bolt is the part #Y52FR.

view full answer...

Answer 2

To fit past the rear spare of your 2021 Jeep Wrangler the Yakima EXO rack part #Y44ZR that you referenced would require you to use the Yakima StraightShot hitch extender part #Y69VR. This would add 7-1/4 inches to the current shank length which would…

view full answer...

Answer 3

The Yakima EXO SwingBase Swing Away Hitch Extender item #Y34VR you were looking at does not reduce your tongue weight capacity by 50%. The only reduction it would cause to your 350 lbs capacity would be the 65 lbs weight of the EXO SwingBase itself.…

view full answer...

Answer 4

Actually the lock cylinder you see in the picture you attached actually pulls out as a cable lock that you route around the bikes and then lock back to the arm like what you see in the attached picture.

view full answer...

Answer 5

Because using an adapter like the #C45770 adds another piece to the connection between the hitch receiver tube and the hitch mounted accessory (bike rack in this instance), you will tend to get some more movement than you normally would. If you were…

view full answer...

Answer 6

I discussed your project with Yakima and to complete your conversion you will need Yakima part numbers; #8880828 Rear Tray, #Y82FR Arm, #8880835 Cable Lock, #Y22FR Arm Lock, and #Y54VR hardware. Since that time I have asked our inventory managers to…

view full answer...

Answer 7

A typical carry-on is 22" X 14" X 9". The gear locker of the Yakima EXO Swing Away Storage System w/ Enclosed Cargo Carrier and Cargo Carrier - 2" Hitches, part #Y44ZR, has the following dimensions, 23" X 60" X 16".…

view full answer...

Answer 8

The Yakima BackSwing Swing Away Hitch Extender #Y02483 will allow you to open the rear hatch on your JLU Wrangler Sahara. This will work with cargo carriers or bike racks that use a 2" receiver. Do note that depending on your gear loaded you may…

view full answer...

Answer 9

Yes! We do have those parts for your Yakima SwingBase #Y34VR. The replacement parts you need the Replacement Anti-Rattle Hitch Bolt and Washer for Yakima HangOver Bike Rack #Y52FR (Yakima part 8880953) and the Replacement Hitch Bolt Threaded Insert…

view full answer...

Answer 10

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 11

If you are needing the hub and drum assembly then you will want to go with the Dexter Trailer Hub and Drum Assembly #8-201-5UC3-EZ but if you are just looking for an idler hub then you will want part #8-213-5UC1 instead. These come with the correct…

view full answer...

Answer 12

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Can the Replacement Cable Lock Assembly for the Yakima HoldUp Bike Carrier be Keyed Alike

Product Page this Question was Asked From

Continue Researching