Torque Specs for Wet Bolts for Dexter Axle E-Z Flex Suspension Kits

Question

Question:

I have a 2018 Cedar Creek with the 8000lb axel and the dexter ezfelx suspension on it. I have noticed that the front and rear shackle bolts are working loose. What is the torque spec for these bolts?

asked by: Robert B

0

Expert Reply:

According to the installation instructions from Dexter Axle the torque specs for the wet bolts on their Dexter E-Z Flex Suspension Kits, like part # K71-653-00, is 30 - 50 ft-lbs. I have attached a clip from their instructions for you to check out.

expert reply by: Jon G

0

click to enlarge

Answer 1

There is no specific torque rating for shackle bolts. You'll want to ensure that the bolts you use are long enough so that when installed you will have at least 2 threads protruding from the nut. Make sure that the bolt you're using has a…

view full answer...

Answer 2

For 9/16 inch suspension bolts, wet bolts or regular bolts, you will want to torque them to 65 to 95 foot pounds. And should you ever use 1/2 inch bolts then the torque spec is 45 to 70 foot pounds. And for 5/8 inch use 100 to 120 foot pounds.

view full answer...

Answer 3

I spoke with the manufacturer and they recommend using 160 ft-lb for the torque spec on a 3/4 inch U-bolt #11-70.

view full answer...

Answer 4

We carry all sorts of RV door parts including hinges and latches that you can see on the linked pages. I included links to hinges, latches and weather-stripping like #WS1434 and vinyl trim like #CAM25103. Since trailer makers do not keep track of…

view full answer...

Answer 5

To find the correct E-Z Flex Equalizer, you will need to take off your current ones and measure the distance from the center of the one end hole to the center of the other. You will also need to ensure that your leaf springs are 1-3/4" wide.…

view full answer...

Answer 6

Torque specs for wheel lug nuts will vary depending on the diameter of the lugs, type of lug nut and the wheel's material. The linked chart details the recommended torque for many combinations. Dexter Hub/Drum #84546UC3 has 1/2-inch studs and…

view full answer...

Answer 7

You can verify that the 10-19 grease seal included in Bearing Kit #BK2-100 is the correct one for your spindles by taking two measurements. First you want to measure the rear hub bore where the seal is inserted. The seal's outer diameter needs to…

view full answer...

Answer 8

The torque for the Dexter Trailer Hub and Drum Assembly - 6,000-lb and 7,000-lb Axles - 12" - 5 Spoke Utility #8-174-5UC3 is not specified by the manufacturer. For 9/16 inch studs, the typical lug nut torque will be 120-140 ft lbs based on most…

view full answer...

Answer 9

It is completely within the realm of possibilities that the actuator has become disconnected from the gate internally causing the valve to not open. The Valterra Waste Valve Body for RV Black Water Tank w/ Coupler, Seals, and Hardware - 3"…

view full answer...

Answer 10

There is no YMM fit guide for the Replacement Dexter Bolt-On Shock Kit #K71-697-00 so I won't be able to say for certain, however if as long as you have either 2-3/8" or 3" diameter axles with 1-3/4" wide springs these'll fit.

view full answer...

Answer 11

To correctly measure a leaf spring, you'll want to jack the trailer up on jack stands so the axle is hanging freely, then measure directly across from the center of one spring eye to the other, as shown in the provided diagram. The height of the…

view full answer...

Answer 12

Yes, you can use the 4-Leaf Spring part #e22YR on your trailer. The overall length matches what you need and the capacity is close enough to your axle capacity that it would work well in that regard as well. It would have 500 more lbs than what your…

view full answer...

Torque Specs for Wet Bolts for Dexter Axle E-Z Flex Suspension Kits

Product Page this Question was Asked From

Featured Help Information

Instructions

Miscellaneous Media

Continue Researching