Anti-Rattle Hitch Lock for Kuat Hi Lo Adapter # HL20b

Question

Question:

Hello, I have a Kuat hi-lo for my Kuat nv 2.0, and I wonder if the Anti-Rattle Hitch Lock for Kuat Transfer Bike Racks - HLT series would work on the Kuat hi-lo. I think it would but all I see is reference for the Kuat transfer. Thank you in advance.

asked by: Valentin

0

Expert Reply:

You can use the Kuat Hitch Lock part # HLT with the Kuat Hi Lo Adapter part # HL20B that you have. It's the same hitch pin design so it would work.

expert reply by: Jameson C

0

Answer 1

Yes, the shank on your Kuat Transfer 2 Bike Platform Rack will work on the receiver tube opening of the Kuat Hi-Lo 2" Hitch Extender part #HL20B. For a lock, you can use the Anti-Rattle Hitch Lock for Kuat Transfer and NV Core Bike Racks part…

view full answer...

Answer 2

The Timbren Axle-Less Trailer Suspension System #A35RD545E that you referenced uses inner bearing #L68149 and outer bearing part #L44649. It sounds like you are asking about the outer bearing. The wheel will need to be at least 13 inches in diameter…

view full answer...

Answer 3

I suggest the Curt Trailer Hitch Receiver Class III Part #C13409. The reason being, the measurement from the center of the hitch pin hole, to the edge of the bumper has been measured at approximately 4". The measurement with the Draw-Tite option…

view full answer...

Answer 4

If you have a Kuat Transfer 2 Bike Platform Rack like part #KU74FR and need to lower the platform height then there is actually an adapter specifically for this, the Kuat Hi-Lo Hitch Extender part #HL20B. This will lower the bike rack 2-1/8" but…

view full answer...

Answer 5

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 6

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 7

From what I could find it looks like your 122R (red) and 122Y (amber) lights measure 3.75" x 1.70" x .81". We don't have any replacement lense directly for the GLO-BRITE lights but we do have some similar lights that you could use…

view full answer...

Answer 8

Seal 171255UC has an inner diameter of 1.719 inches and outer diameter of 2.565 inches. A seal that has those dimensions would actually be #58846. I've added a link to a video review of this seal for you to take a look at.

view full answer...

Answer 9

If you are needing the hub and drum assembly then you will want to go with the Dexter Trailer Hub and Drum Assembly #8-201-5UC3-EZ but if you are just looking for an idler hub then you will want part #8-213-5UC1 instead. These come with the correct…

view full answer...

Answer 10

I would be happy to help you set up your 2022 Toyota Highlander to haul your new travel trailer. The wiring harness you currently have controls your trailer's lighting functions only. You do not need to rewire your Toyota you just need another…

view full answer...

Answer 11

Unfortunately there are no plug-in adapters or harnesses that would allow you to replace the factory 4-way flat trailer connector with a 7-way or a 7-way and 4-way connector on your 2005 Ford F-150. To complete the installation for a brake controller…

view full answer...

Answer 12

The correct replacement master cylinder kit we have for your Demco setup is the part #DM5918 which comes with the lock out replacement.

view full answer...

Anti-Rattle Hitch Lock for Kuat Hi Lo Adapter # HL20b

Products Referenced in This Question

Product Page this Question was Asked From

Featured Help Information

Miscellaneous Media

Continue Researching