Lighter Duty Worm Gear Winch Availability

Question

Question:

Hi....im trying to find a very small worm gear winch that only needs to be rated for two hundred pounds. Is this possible?

asked by: Gary B

0

Expert Reply:

The smallest rated worm gear winch we have is 1,500 lbs like the part # DL10950 that you referenced. While this is a bit overkill for the weight you need it would still work well. For a 25 foot long cable you'd then want the part # DL24100.

expert reply by: Jameson C

0

Answer 1

There are a few ways brake winches operate but the worm gear winches like the part #DL10950 that you referenced have the most effective brake since the handle turns a worm gear which rides on a sprocket that is attached to the drum. Basically if the…

view full answer...

Answer 2

I have attached the review video of the Dutton-Lainson Hand Winch part #DL10950 to this answer page for you. The video can be found in the middle of the page under the "Featured Help Information" heading. As mentioned, the above worm gear…

view full answer...

Answer 3

The correct replacement master cylinder kit we have for your Demco setup is the part #DM5918 which comes with the lock out replacement.

view full answer...

Answer 4

The number you provided, "7753400" is a patent number which corelates to the Equalizer for E-Z Flex Suspension part #013-144-03. This is for a single equalizer but if you need the entire kit it's the Dexter E-Z Flex Suspension Kit part…

view full answer...

Answer 5

You will have to go with a sliding hitch to allow the trailer to make tight turns. For a trailer 8 feet wide the only bed length that's going to allow 90 degree turns without a slider is a stationary hitch. That being said you have two options.…

view full answer...

Answer 6

For your enclosed trailer application I have several suggestions for adding interior lighting that you can control directly via a switch. Since your current 4-pole trailer wiring does NOT include a 12V auxiliary power feed that could power inside…

view full answer...

Answer 7

The only way you could power interior dome lights on a trailer without it being connected to a tow vehicle would be to power the lights with a battery like a breakaway battery. How you choose to wire up the batteries will in the end be up to you, but…

view full answer...

Answer 8

The Tekonsha OEM Vehicle Wiring Harness #22121 that you referenced includes all the wiring and parts necessary to install a fully functional 7-Way connector and trailer brake controller. The included brake controller harness is compatible with and…

view full answer...

Answer 9

By "mobile home type bolt pattern" I believe you are talking about a 5 spoke utility bolt pattern such as what is on the Dexter Trailer Hub and Drum Assembly - 6,000-lb and 7,000-lb Axles #8-174-5UC3. To measure your axle from hub face to…

view full answer...

Answer 10

So for your set up, a 2021 Ram 2500 short bed with the RamBoxes, you will need to use a Sidewinder in order to have the clearance to tow a 5th wheel. The Goose Box doesn't move the pivot point and an offset ball just won't be enough for…

view full answer...

Answer 11

Brake systems are not dependent on the hub bolt pattern. So you can use the Electric Trailer Brake Kit #AKEBRK-7-SA for 12 inch hub/drums or #AKEBRK-35-SA for 10 inch hub/drums. Then use #10-1-1 wire sold by the foot for your brake magnet wiring.…

view full answer...

Answer 12

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Lighter Duty Worm Gear Winch Availability

Products Referenced in This Question

Product Page this Question was Asked From

Featured Help Information

Instructions

Miscellaneous Media

Continue Researching