Recommended Spare Tire Carrier for the Roadmaster Tow Dolly RM3477

Question

Question:

Will the RM2007 fit my RM 3477 DOLLY, The young is 3X3. Thanks.

asked by: Tom J

1

Helpful Expert Reply:

Yes, the Spare Tire Carrier for Roadmaster Tow Dollies part # RM-2000-7 will work with the Roadmaster Tow Dolly with Electric Brakes (RM3477) part # RM-2050-1. For a spare wheel/tire you can use the Spare Tire and Wheel for Roadmaster Tow Dolly part # RM-200330-80.

expert reply by: Conner L

1

Answer 1

We don't carry a cover for a tow dolly specifically. We do carry storage covers for pop-up campers and that is probably the best option for what you are seeking. I recommend the Camco UltraGuard Pop-Up Camper Cover - 6'-8' Long #CAM45760…

view full answer...

Answer 2

The main difference between the Dometic 310 Part-Timer RV Toilet #DOM57FR and the Dometic 311 Part-Timer RV Toilet #DOM67FR is that the 310 is standard height (20" tall) and the 311 is a low profile (15-1/2" tall). Both toilets will mount…

view full answer...

Answer 3

For your GC2 Deep Cycle Extreme GC2-ECL-UTL battery, I recommend the Snap-Top Battery Box with Strap for 6V Batteries - Vented, part #329-HM306BKS. It is compatible with battery sizes ranging from 8-5/8" long x 9-5/8" tall x 5-5/8"…

view full answer...

Answer 4

The mounting plate of the Spare Tire Carrier for Roadmaster Tow Dollies #RM-2000-7 that you referenced measure 3 inches apart left to right and 3-1/2 inches apart front to back. It's designed to fit 3 inch frame.

view full answer...

Answer 5

The spare tire can be mounted near the wheel and axle to the frame, but you will want more than 5 inches of ground clearance. I recommend the Extra Offset Trailer Spare Tire Carrier by Dutton-Lainson #DL22145 based on your photo. Every extra inch…

view full answer...

Answer 6

I've never heard of an actual third brake light connector on a camper shell to plug in on a truck and we don't carry any parts to do that. The light generally needs to be hardwired into the truck's brake light circuit. The issue with this…

view full answer...

Answer 7

I did some checking and the hub/drum we offer that will work for you is the part #8-430-5UC3. This uses the same bearings as the 8-415 and will be an exact fit aside from the fact this is a non-ABS setup and the 8-415 came in an ABS setup and non-ABS…

view full answer...

Answer 8

Since Demco uses 3,500 drum brake assemblies part #DMSB24429M and #DMSB24428M what you'd need is similar 3,500 electric brake assemblies like the etrailer part #AKEBRK-35L-SA for the left hand side and #AKEBRK-35R-SA for the right hand side. To…

view full answer...

Answer 9

If your current springs have 5 leaves then going to a 7 leaf spring will increase the height of the trailer a little and make the trailer more susceptible to sway. Regarding capacity if you go with springs rated higher than what is required it will…

view full answer...

Answer 10

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 11

Since you have a wheelbase/axle spacing of 38 inches the correct hanger kit for slipper springs would be the part #HAP-105-205-01. And then for a 7k trailer axle the u-bolt kit you'd want would be the part #APUBR-8. I attached the diagram to use…

view full answer...

Answer 12

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Recommended Spare Tire Carrier for the Roadmaster Tow Dolly RM3477

Products Referenced in This Question

Product Page this Question was Asked From

Featured Help Information

Instructions

Continue Researching