Replacement Parts for the Bulldog Powered Drive Trailer Jack part BD500199

Question

Question:

Purchased a Bulldog 500199 jack in 2016. Love it, use it often. Unfortunately, the connector went bad little black box under the cover with two wires. Is there a replacement part available?

asked by: Merry B

0

Expert Reply:

I have attached for you a list of the replacement parts that are available for the Bulldog Powered Drive Trailer Jack part # BD500199. I am not sure which part in particular that you are referring to but if it is not listed below then you would unfortunately have to replace the jack. The Ultra-Fab Electric A-Frame Jack part # UF38-944014 would be a good cost effective replacement for this if needed.

Replacement Extend and Retract Switch part # BD500363
Replacement Manual Override Crank part # BD500203
Replacement Manual Override Cover part # BD500201
Replacement Level Assembly part # BD500193
Replacement Light Switch part # BD500362
Replacement Spring Loaded Pull Pin part # BD500388

expert reply by: Conner L

0

Eddie C.

8/9/2020

I have a Bulldog 500199. I need everything except the motor. Is it possible to find the jack w/o the motor?

Reply

Jon G.

8/19/2020

We have a few replacement parts for the Bulldog Powered Drive Trailer Jack # BD500199 but they are things like switches or plugs. I'm not aware of a replacement part that includes everything but the motor. The only way that I can see this being possible is if you looked at a resale shop or maybe someplace where people sell used parts.

Reply

Kevin D.

4/17/2020

I have a jack 500199 and the screw broke I cant find a screw or a screw and nut assembly. Can you help?

Reply

Chris R.

4/18/2020

I did some further research and it does look like the above mentioned parts are all that's available for the Bulldog Jack # 500199. If the internal screw and nut is damaged, the entire jack will need to be replaced. I wish I could have given you better news.

Reply

Answer 1

I confirmed with Fulton that the part you need is the Replacement Endcap for Fulton Round, Swivel Marine Jacks #F500324.

view full answer...

Answer 2

Either something happened to the wiring of the jack when it bottomed out or the switch went out on your #BD500199. The replacement switch is part #BD500363. If the light doesn't work either then I'd say it's wiring related and you'd…

view full answer...

Answer 3

When an electric trailer tongue jack like the Barker VIP 3500 will not operate with electric power the two most common causes are a weak ground connection or a battery with an insufficient charge. I checked the online installation/operation…

view full answer...

Answer 4

I've never heard of an actual third brake light connector on a camper shell to plug in on a truck and we don't carry any parts to do that. The light generally needs to be hardwired into the truck's brake light circuit. The issue with this…

view full answer...

Answer 5

If you are needing the hub and drum assembly then you will want to go with the Dexter Trailer Hub and Drum Assembly #8-201-5UC3-EZ but if you are just looking for an idler hub then you will want part #8-213-5UC1 instead. These come with the correct…

view full answer...

Answer 6

If the trailer wheels scrubbed (dragged and scrapped the ground instead of rolling) when jack knifed then it could have thrown something out of alignment or damaged something. First, inspect the suspension. Look for any elongated holes where…

view full answer...

Answer 7

I would be happy to help you set up your 2022 Toyota Highlander to haul your new travel trailer. The wiring harness you currently have controls your trailer's lighting functions only. You do not need to rewire your Toyota you just need another…

view full answer...

Answer 8

I did some checking and the hub/drum we offer that will work for you is the part #8-430-5UC3. This uses the same bearings as the 8-415 and will be an exact fit aside from the fact this is a non-ABS setup and the 8-415 came in an ABS setup and non-ABS…

view full answer...

Answer 9

To tow your trailer that uses an RV style 7-way blade style connector with your semi that has a 7-pin connector, you need to construct an adapter that will also combine the brake signal into the right and left directional signal pins. This can be…

view full answer...

Answer 10

Since you have a wheelbase/axle spacing of 38 inches the correct hanger kit for slipper springs would be the part #HAP-105-205-01. And then for a 7k trailer axle the u-bolt kit you'd want would be the part #APUBR-8. I attached the diagram to use…

view full answer...

Answer 11

I have a solution for you, but we do not carry Glo-Brite lights, so replacing it with the same brand will not be something I can offer you. Instead, to replace your Glo-Brite 9852-88, I recommend using the Optronics LED Trailer Tail Light #STL72RB.…

view full answer...

Answer 12

The manual lockout on your Atwood 85778 surge brake coupler is there so that you can back up the trailer without the brakes locking up on you. Yes you can safely tow your trailer with the broken manual lockout, you just have to make sure you…

view full answer...

Replacement Parts for the Bulldog Powered Drive Trailer Jack part BD500199

Products Referenced in This Question

Product Page this Question was Asked From

Featured Help Information

Instructions

Continue Researching