Installation of Lippert Flexguard RV Slide-Out Kit Hardware
Question:
How does this attach at both ends? And where to attach as a blowen tire broke all the flex guard off at atboth ends. Thanks for input.
asked by: Ron C
Helpful Expert Reply:
I have attached photos of the installation instructions of the Lippert Components Single Flexguard RV Slide-Out Kit Hardware # LC1346271, and also sent you a link which has the install instructions you can check out. The instructions are as follows:
Installation
Note: Variations from the install, unless otherwise approved by LCI Engineering, will not be covered under
warranty.
1. Position Flex Guard under the slide-out room where the wiring or hoses to be protected are located.
2. Insert the aluminum pin (Fig. 1A) into the Flex Guard (Fig. 1B) with the mounting bracket (Fig. 1C)
facing up. Slide the star washer (Fig. 1D) over the end of the pin at the bottom of the Flex Guard and
push in place.
3. Slide the Flex Guard clips (Fig. 1E) onto the end of the Flex Guard with the holes in the clips facing the
direction of the hoses and wiring to hold them in place. Space all clips evenly throughout the length of
the Flex Guard.
4. Install Flex Guard mounting bracket (Fig. 1C) to the bottom of the unit floor, perpendicular to the
outrigger and furthest away from the I-beam or room bar, using four #10 x 1" self-tapping screws or
#10 x 1" wood screws (Fig. 2A).
5. Mount the flat end of the Flex Guard to the LCI-supplied mounting plate (Fig. 3A) mounted offset to
the aluminum pin (Fig. 1A) at the opposite end using two #10 x 1" self-tapping screws (Fig. 3B) per belt
section. Install the LCI-supplied mounting plate to the bottom side of the slide-out room.
6. Slide any hoses and wiring through the holes in the Flex Guard clips when installing in order to protect
hoses and wiring with the Flex Guard.
7. Flex Guard should be kept parallel to the slide room floor.
8. Make sure the flat end of the Flex Guard is mounted several inches away from the direction of the bend
of the retracted Flex Guard (Fig. 4).
Charles W.
1/26/2020
I have no oem supplied bracket to mount the flat end of the flexguard. Where can I purchase one?
Product Page this Question was Asked From
Lippert Components Single Flexguard RV Slide-Out Kit Hardware
- RV Slide Out Parts
- Hardware
- Flexguard
- Lippert
more information >
Featured Help Information
Instructions
Continue Researching
- Search Results: 274~000006
- Shop: Lippert Components Single Flexguard RV Slide-Out Kit Hardware
- Shop: Lippert Double Flexguard RV Slide-Out Kit Hardware
- Search Results: license plates and frames
- Search Results: 25712610
- Shop: Jensen RV Stereo w DVD Player - Double DIN - App Control, Bluetooth, HDMI - 160W - 3 Zones - 12V
- Shop: Replacement Control Unit for Kwikee Revolution Series Electric RV Steps
- Shop: Replacement Motor with Box Brackets for Kwikee 42 Series Electric RV Steps - 12V
- Shop: Replacement Motor for Kwikee Revolution Series Electric RV Steps - 12V
- Search Results: 380073
- Search Results: 1510000172
- Shop: Lippert In-Wall RV Slide-Out Motor
- Search Results: 364262
- Search Results: 236575
- Video: Quest Audio Video RV Stereos - In-Wall Stereo - 292-101809 Review
- Video: Diamond Trailer Lights - Tail Lights - DG52448PB Review
- Video: Review of MORryde Safe-T-Rail Telescoping RV Handrail - MR54BR
- Video: Lippert Double Flexguard RV Slide-Out Kit Hardware Review
- Q&A: Recommended Flat Towing Setup For A 2023 Jeep Wrangler 4XE
- Shop: Brake Controller
- Q&A: Mounting Measurements for Lippert Manual Pull-Out Step LC432690
- Q&A: Replacement Lippert Triple Pull Out/Manual RV Steps
- Video: Lippert Components RV and Camper Steps - Motorhome - LC432690 Review
- Video: Lippert Solid Stance RV Step Support Kit Review
- Video: JR Products Spring-Loaded RV Cabinet Catch Installation
- Shop: RV Furniture
- Q&A: Replacement Slide-Out Hardware Kit
- Q&A: How to Get Wires Through The Lippert Double Flexguard RV Slide-Out Kits Brackets
- Shop: Tire Chains
- Shop: Trailer Wiring
Joe D.
6/11/2020
I bought a flexguard slideout kit to replace the one Actualy under my slideout on a Catalina 39 mkts. The rubberband is in good sape only the plastic brakets are broken. How do I get the cable through the plastic ring.