Does Installing Curt Trailer Hitch on 2019 Subaru Crosstrek Affect Rear Crumple Zone Integrity

Question

Question:

I just purchased a 2019 Subaru Crosstrek and plan to install a Curt hitch mainly to carry bicycles, minimum towing. Subaru stated their OEM hitch is installed in-line with the frame which maintain the integrity of the rear crumble zone. The Curt C1338 hitch is mounted below the frame. Does the Curt hitch affect the safety of the crumble zone in an accident? Thank you.

asked by: Wai T

0

Expert Reply:

The install of the Curt 2-inch hitch part # C13382 that you referenced on your 2019 Subaru Crosstrek would not negatively affect the crumple zone of the rear bumpers. This attaches to the bottom of the vehicle frame where a hitch was designed to attach by Subaru. If you were rear-ended the hitch would provide a bit more rigidness but it would still crumple like it would need to and be safe.

expert reply by: Jameson C

0

Answer 1

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 2

The spacers that come with the etrailer hitch that fits your 2022 Subaru Crosstrek are designed to be used as a way to level the hitch as needed. So if using them causes your hitch to not sit level I would recommend removing them.

view full answer...

Answer 3

I took a look in the owners manual of your 2018 Subaru Crosstrek and found that it has a 200lb tongue weight rating, so while the etrailer Trailer Hitch #e98912 has a much higher 525lb tongue weight rating you will still be limited to the lower…

view full answer...

Answer 4

You are correct, hitches for the 2022 Subaru Crosstrek like the etrailer Trailer Hitch Receiver #e98912 have a max tongue weight over 500 lbs, or in this case 525 lbs. This is simply the tongue weight capacity of the hitch itself. The capacity is…

view full answer...

Answer 5

I pulled one of the Curt Skid Shields from our warehouse, and took the measurements you see in the photo. Overall, the item is about 8-3/8 inches long. The distance from the hitch pin hole to the closest portion of the skid plate at the bottom is 3…

view full answer...

Answer 6

The return line when using a snatch block on the Curt Front Mount Trailer Hitch Receiver part #C31075 for a 2023 Toyota Tacoma should be attached to the tow hooks on the vehicle, not the loops on the receiver per the instructions. The hitch as you…

view full answer...

Answer 7

I checked with Curt for you, the Curt Front Mount Trailer Hitch Receiver part #C31075 is a confirmed fit for a 2023 Toyota Tacoma all models including a TRD Off-Road. This front mount hitch will be a great addition to your Tacoma allowing you to do a…

view full answer...

Answer 8

For a 12,000 lb. electric car trailer winch like the Bulldog Winch Trailer Winch part #BDW10040, I recommend a standard 12 volt lead acid battery rated up to at least 650 cold cranking amps (CCA). As long as the battery is rated up to 650 CCA then…

view full answer...

Answer 9

You will need the Red LED Trailer Clearance or Side Marker Light #328-K-52 or Amber LED Trailer Clearance or Side Marker Light #328-K-51 for your 2018 Forest River Sunseeker motorhome. These lenses have the same Top Command SAE-AP2-16 markings on the…

view full answer...

Answer 10

I've never heard of an actual third brake light connector on a camper shell to plug in on a truck and we don't carry any parts to do that. The light generally needs to be hardwired into the truck's brake light circuit. The issue with this…

view full answer...

Answer 11

I did some checking and the hub/drum we offer that will work for you is the part #8-430-5UC3. This uses the same bearings as the 8-415 and will be an exact fit aside from the fact this is a non-ABS setup and the 8-415 came in an ABS setup and non-ABS…

view full answer...

Answer 12

If you are needing the hub and drum assembly then you will want to go with the Dexter Trailer Hub and Drum Assembly #8-201-5UC3-EZ but if you are just looking for an idler hub then you will want part #8-213-5UC1 instead. These come with the correct…

view full answer...

Does Installing Curt Trailer Hitch on 2019 Subaru Crosstrek Affect Rear Crumple Zone Integrity

Product Page this Question was Asked From

Featured Help Information

Instructions

Miscellaneous Media

Continue Researching