Troubleshooting Kwikee Revolution Step Chattering on a 2013 Winnebago

Question

Question:

2013 Winnebage 2 step Kwikee 90100004s4 step double ....bounces at end of retraction under coach and extention out. Removed motor, steps go in and out freely. Should I just replace motor? Thank you

asked by: Keith T

0

Expert Reply:

It sounds like you are experiencing chattering on your Kwikee Revolution double step. I reached out to my contact at Lippert who said that when the steps start acting like that the motor does need to be replaced. According to the 901 number you gave me and that the steps are on a 2013 Winnebago my contact said that your Revolution steps need the replacement motor # LC380073.

expert reply by: Jon G

0

Answer 1

I spoke with my contact at Lippert who said that using the correct motor (part #LC380073) will help to fix the issues you are having with your Revolution Power Step #LC3725791 but you will also need to adjust your cams to remove some of that play you…

view full answer...

Answer 2

From what you describe I suggest you examine the motor and gears as it appears they are worn. The Replacement Motor for Kwikee Revolution Series Electric RV Steps, #LC380073 is the correct part number. Or, for a complete replacement of Kwikee…

view full answer...

Answer 3

Sounds like you have the now discontinued Atwood landing gear set that had 36 inch overall length outer tube lengths. The good news is that we have landing gear sets that will easily replace what you have but the outer jack length will be different.…

view full answer...

Answer 4

I was not able to reference the part number "VMI900L" but in order to determine if the Replacement Follow Jack w/ Drop Leg part #LG-179014 is the correct replacement for you, you will need to measure the distance between the bracket stops…

view full answer...

Answer 5

If you need to replace the slave leg in your landing gear set up then you can use Stromberg Carlson, #LG-179014, will fit. The lead leg would be #LG-179013. Each leg has a 3,000 pound capacity. These legs have many of the same parts because there is…

view full answer...

Answer 6

Sounds like the correct follower leg you would need is the #LG-179014 that you referenced. The overall length of the leg is 33-1/2 inches and the distance from the inside of the two brackets is 17-1/2 inches. Check out the picture I attached for more…

view full answer...

Answer 7

To determine the correct replacement landing gear for your 5th wheel trailer, you will need to measure the mounting brackets on your trailer from the underside of the top bracket to the top of the lower bracket as shown in the diagram. From there you…

view full answer...

Answer 8

According to my contact at Stromberg Carlson, their #LG-179014 follower leg would indeed be an acceptable replacement for your Venture #900-40L if the 29-1/2 inch outer tube and overall heights of 33-1/2 match your existing jack. You can see these…

view full answer...

Answer 9

You will either need to connect to your truck or have another stabilizer to support the weight when you remove the landing gear. The lead or follow leg can then be removed by loosening the welded brackets that hold the leg in place and move them…

view full answer...

Answer 10

For your Venture landing gear set the correct follower leg you'd need is the part #LG-179014 which matches what you sent in a picture of.

view full answer...

Answer 11

Based on your picture the replacement motor you need is actually the part #LC380073. This would explain why the #LC379608 that you referenced is not fitting at all.

view full answer...

Answer 12

Thanks for the picture! Based on that I was able to determine that the kit you need is the part #LC380073. The cog or gear you mentioned is not available separately so this would be only way to fix your steps.

view full answer...

Troubleshooting Kwikee Revolution Step Chattering on a 2013 Winnebago

Product Page this Question was Asked From

Continue Researching