Will the SilverBack RV Sewer Hose Kit Fit In a 4 x 4 Square Bumper

Question

Question:

Can this hose with fittings be stored in standard RV 4inch square bumper?

asked by: Frank G

1

Helpful Expert Reply:

Yes, you can store the SilverBack RV Sewer Hose Kit w/ Swivel Fittings part # D04-0650 in a standard 4" x 4" bumper. However, you will need to remove the 90 degree elbow fitting most likely and store it somewhere else in order to do so. Please note we also offer extensions for this sewer hose as well, part # D04-0602 for 2' long or part # D04-0605 for 5' long.

expert reply by: Conner L

1

Answer 1

There are great options for spare tire carriers on your trailer, but I do not recommend using the Buyers Products Spare Tire Carrier #3375201010 or mounting it under a trailer. Bolting it on, in particular, is not something you would want to do in…

view full answer...

Answer 2

I've never heard of an actual third brake light connector on a camper shell to plug in on a truck and we don't carry any parts to do that. The light generally needs to be hardwired into the truck's brake light circuit. The issue with this…

view full answer...

Answer 3

I did some checking and the hub/drum we offer that will work for you is the part #8-430-5UC3. This uses the same bearings as the 8-415 and will be an exact fit aside from the fact this is a non-ABS setup and the 8-415 came in an ABS setup and non-ABS…

view full answer...

Answer 4

Since you have a wheelbase/axle spacing of 38 inches the correct hanger kit for slipper springs would be the part #HAP-105-205-01. And then for a 7k trailer axle the u-bolt kit you'd want would be the part #APUBR-8. I attached the diagram to use…

view full answer...

Answer 5

Yes, the best option we can offer you to add fuel capacity is with the DeeZee Truck Bed Auxiliary Tank part #DZ91752X which should fit in the space you have between the cab and 5th wheel hitch no problem as it is only 9" deep. I don't have…

view full answer...

Answer 6

I would be happy to help you set up your 2022 Toyota Highlander to haul your new travel trailer. The wiring harness you currently have controls your trailer's lighting functions only. You do not need to rewire your Toyota you just need another…

view full answer...

Answer 7

Since Demco uses 3,500 drum brake assemblies part #DMSB24429M and #DMSB24428M what you'd need is similar 3,500 electric brake assemblies like the etrailer part #AKEBRK-35L-SA for the left hand side and #AKEBRK-35R-SA for the right hand side. To…

view full answer...

Answer 8

The two sizes you mentioned are pretty similar and fit many of the same 15 inch wheels. The 205/75-15 fits rim widths of 5 inch to 6-1/2 inch whereas the 225/75-15 fits widths that are 5 inch to 6 inch. The 205 is 27.1 inches tall and the 225 is 28.4…

view full answer...

Answer 9

As far as height adjustability and weight capacities the Curt Q20 #C16130 and the Curt A20 #C16140 are identical. They both have a Gross Towing Weight of 20,000 lbs, a Vertical Load Limit of 5,000 lbs, and a height range of 13-17 inches. When it…

view full answer...

Answer 10

A 4-way trailer connector will have four functions which means it will also have four wires for the exception of wishbone harnesses. These four functions are ground, tail light, right turn, and left turn. The ground function will usually be…

view full answer...

Answer 11

To determine which brake assemblies would be needed, you will need to measure your existing brake drums as shown in the provided photo. Since your trailer has a 14,000 lb capacity, you most likely have tandem 7,000 lb axles, which typically use a…

view full answer...

Answer 12

The Replacement Amber Lens for MC32AB Trailer Lights #A32AB is a direct replacement for the SAE A P2 DOT 14 and would be what you'd need.

view full answer...

Will the SilverBack RV Sewer Hose Kit Fit In a 4 x 4 Square Bumper

Products Referenced in This Question

Product Page this Question was Asked From

Continue Researching