Recommended Electric Winch For a Lund Boat Trailer

Question

Question:

Hello, I have a 2018 Lund boat that I want to install a winch on. How long is the longest belt you have for an electric winch? My trailer does not have rollers it has skids that the boat sets on instead - if that matters.

asked by: Mark S

0

Expert Reply:

The Dutton-Lainson StrongArm Electric Winch part # DL25200 is a great electric winch for a boat trailer and it comes with a 20' strap. It also has a 4,000 lb weight which will be plenty for most small-medium boats.

expert reply by: Conner L

0

click to enlarge

Answer 1

The only repair kit we have for your Profile 2000 hand winch is the Winch Ratchet Repair Kit by Dutton-Lainson item #DL70475. If this isn't what you are needing you will have to replace your winch. I recommend the Dutton-Lainson Hand Winch…

view full answer...

Answer 2

I went out into our warehouse to grab a Dutton Lainson Winch part #DL14627 to measure the bolt hole dimensions for you. I attached a picture that has all of them listed.

view full answer...

Answer 3

I reached out to my contact at Dutton-Lainson and the Dutton-Lainson Covered Hand Winch - 2 Speed - Freewheel - 25' Strap - 2,600 lbs #DL17085 will mount the same as your current DL1802A #DL14627. With that said the #DL17085 will be about…

view full answer...

Answer 4

While you never want to exceed an item's working load limit (WLL) in your actual application, the nature of your trailer matters too when selecting a winch strap. If you have roller bunks rather than carpeted bunks this reduces friction and…

view full answer...

Answer 5

We carry several trailer fender bracket options you could use to install the Fenders #CE19502-2 which I attached a link to on this page. The most popular option is the larger L-bracket part #CE26061G-2. I attached an install video for these for you…

view full answer...

Answer 6

So, just to make sure we're on the same page, the correct wiring harness for your Dutton-Lainson TW4000 StrongArm Electric Winch #DL25200 manufactured before 2014 is the Dutton-Lainson Wiring Harness for StrongArm Electric Winch Model TW4000…

view full answer...

Answer 7

The rollers that you need based off of the measurements in your photo is Yates Ribbed Wobble Roller part #YR530R-8P which is a 3x5" ribbed roller with a 1" shaft opening. The fender is a bit harder for me to confirm without measuring. It…

view full answer...

Answer 8

Since you have a wheelbase/axle spacing of 38 inches the correct hanger kit for slipper springs would be the part #HAP-105-205-01. And then for a 7k trailer axle the u-bolt kit you'd want would be the part #APUBR-8. I attached the diagram to use…

view full answer...

Answer 9

I would be happy to help you set up your 2022 Toyota Highlander to haul your new travel trailer. The wiring harness you currently have controls your trailer's lighting functions only. You do not need to rewire your Toyota you just need another…

view full answer...

Answer 10

I've never heard of an actual third brake light connector on a camper shell to plug in on a truck and we don't carry any parts to do that. The light generally needs to be hardwired into the truck's brake light circuit. The issue with this…

view full answer...

Answer 11

If you are needing the hub and drum assembly then you will want to go with the Dexter Trailer Hub and Drum Assembly #8-201-5UC3-EZ but if you are just looking for an idler hub then you will want part #8-213-5UC1 instead. These come with the correct…

view full answer...

Answer 12

If the trailer wheels scrubbed (dragged and scrapped the ground instead of rolling) when jack knifed then it could have thrown something out of alignment or damaged something. First, inspect the suspension. Look for any elongated holes where…

view full answer...

Recommended Electric Winch For a Lund Boat Trailer

Product Page this Question was Asked From

Featured Help Information

Instructions

Continue Researching