Recommended Grass Catcher for Toro 44 SFS Z-Cut Deck

Question

Question:

Toro 44” sfs deck proline. Model 30340 - 210000293. It has the cut outs as described for the z deck. I was expecting it to be a regular deck. Should I buy the catcher for the z deck?

asked by: Josh E

0

Expert Reply:

Since your Toro has the Z-Cut Deck you definitely want to go with the Rack'em Grass Catcher # RCMMS4-EXS1-TORO over the part # RCMMS4-EXS1. I'm not sure when or why Toro puts the Z-Cut Deck on different mowers but according to your picture that is what you have.

expert reply by: Jon G

0

click to enlarge

Answer 1

The correct catcher will depend on the discharge opening behind that deflector shown in your photo. If it has the deck with a Z-bracket as shown in the provided photo, you'd use #RCMMS4-EXS1-TORO. If it doesn't have the z-slot, but…

view full answer...

Answer 2

Measure the discharge opening of your Exmark Viking Hydro and you'll know which of the two grass catchers is what you need. If you have a 4 inch discharge opening you need the part #RCMMS4-EXS1 or if you have a 5 inch opening you'd…

view full answer...

Answer 3

The Rack'em Grass Catcher for Toro, Bobcat, and Exmark Lawn Mower #RCMMS4-EXS1 that you referenced is a fit for the Bob Cat mower you sent a picture in of. Since your Bob Cat has a standard dock that discharges even with the rear tires this…

view full answer...

Answer 4

The Rack'Em Grass Catcher #RCMMS4-EXS1 will work for your Toro lawn mower if it has a regular deck. If your Toro lawn mower has a Z-cut deck you will need The Rack'Em Grass Catcher #RCMMS4-EXS1-TORO. The best way to determine that fit…

view full answer...

Answer 5

For your Toro Timecutter 16-42Z you need one of the following depending on what kind of deck you have: - Standard Deck #RCMMS4-EXS1 - Z-Cut Deck #RCMMS4-EXS1-TORO

view full answer...

Answer 6

The Rack'em Grass Catcher for Toro Lawn Mower with Z-Cut Deck #RCMMS4-EXS1-TORO will fit your 52 inch Toro Z mower deck if it has the Z-cut deck. If you have the regular deck then you will use #RCMMS4-EXS1 instead. The best way to determine…

view full answer...

Answer 7

We offer 2 different Rack 'Em grass catchers for Exmark mowers. The catcher you need will depend on if the discharge chute is 4 or 5 inches tall. If it's 4 inches, you'd need #RCMMS4-EXS1 or if it's 5 inches, use…

view full answer...

Answer 8

If your Toro Timecutter has the Z cut deck that extends out further than the rear wheel, you'd use the Rack 'Em #RCMMS4-EXS1-TORO catcher. If you have the regular deck, you'd use #RCMMS4-EXS1.

view full answer...

Answer 9

If your Toro Timecutter has the Z cut deck that extends out further than the rear wheel, you'd use the Rack 'Em #RCMMS4-EXS1-TORO catcher. If you have the regular deck, you'd use #RCMMS4-EXS1. The Z deck has notches or slots in it as…

view full answer...

Answer 10

I did some checking and the hub/drum we offer that will work for you is the part #8-430-5UC3. This uses the same bearings as the 8-415 and will be an exact fit aside from the fact this is a non-ABS setup and the 8-415 came in an ABS setup and non-ABS…

view full answer...

Answer 11

Hey Tony, the correct Rack Em Grass Cather for your Toro Grandstand 52 is the part #RCMMS4-EXS1-TORO.

view full answer...

Answer 12

When installing/adjusting the Solera RV Slide-Out Awning #LCV000163285 tension is applied by rotating the awning roller 14 times. This should apply the needed spring tension so that the fabric doesn't billow in the wind or leave enough slack that…

view full answer...

Recommended Grass Catcher for Toro 44 SFS Z-Cut Deck

Products Referenced in This Question

Product Page this Question was Asked From

Featured Help Information

Miscellaneous Media

Continue Researching