Install Location for Kat's Block Heater for 2019 Jeep Cherokee with 2.4 Liter 4 Cylinder Engine

Question

Question:

Whats the location to install this engine heater on a 2019 Jeep Cherokee with the 2.4 liter 4 cyl Engine?

asked by: Dan R

0

Expert Reply:

I checked with Kat's and the cartridge location you need to use to install the Kat's block heater part # KH11812 is the FL location which is "front left" and is on the driver side of the engine facing towards the front of the vehicle.

expert reply by: Jameson C

0

click to enlarge

Answer 1

On the engine block of your 2015 Jeep Patriot there are cartridge holes that the block heater part #KH11812 would slip into. The one you'll use is close in proximity to water jackets in the block so the heat generated ends up warming the coolant…

view full answer...

Answer 2

For your 2019 Jeep Cherokee with a 3.2 liter engine the Kat's heater part #KH11812 is the correct part you'd need. I checked with Kat's and they recommend the Left Rear or Right Rear cartridge. So basically the cartridges on the left or…

view full answer...

Answer 3

For your 2019 Jeep Cherokee with a 3.2 liter engine the Kat's heater part #KH11812 is the correct part you'd need. I checked with Kat's and they recommend the Left Rear or Right Rear cartridge. So basically the cartridges on the left or…

view full answer...

Answer 4

According to the good people at Kat's heater #KH11812 installs at the front, left side of the motor (driver's side). The installation instructions do state to coat with NSCG silicone grease G-624. 1) Locate cartridge hole on the engine block.…

view full answer...

Answer 5

A TCM double-lip grease seal number 127194 has an inner diameter of 1.274-inches and an outer diameter of 1.983-inches according to my research. The available grease seal nearest to those dimensions that we offer is part #RG06-010, which is a…

view full answer...

Answer 6

The part you referenced 127194TB is a double-lip seal with an inner diameter of 1.274-inches and an outer diameter of 1.983-inches. The available seal nearest to those dimensions that we offer is part #RG06-010, which is a double-lip seal sold as a…

view full answer...

Answer 7

From what I could find it looks like your 122R (red) and 122Y (amber) lights measure 3.75" x 1.70" x .81". We don't have any replacement lense directly for the GLO-BRITE lights but we do have some similar lights that you could use…

view full answer...

Answer 8

The Rhino-Rack Roof Rack for Factory Tracks #Y02-490B-NT is going to be your best bet for the tracks on the ARE topper for your 2012 Toyota Tacoma. The weight capacity is 220 lbs like you mentioned, but that's going to be the highest you'll…

view full answer...

Answer 9

I recommend the Redarc Tow-Pro Liberty Brake Controller #RED24FR for your 2023 Toyota Tacoma with the factory tow package. You will be able to connect the wiring using the Redarc Adapter #RED99FR directly to the factory connector. We also have the…

view full answer...

Answer 10

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 11

To determine if the Replacement Shock for Titan Model 6 and 10 Brake Actuators, part #T1242600 will work to replace your Gabriel number 610712 (T2032) shock, you will need to verify a few quick measurements. Part #T1242600 will work as a replacement…

view full answer...

Answer 12

The modern size equivalent of the 20.5x8-10 that you have currently would be the same size tire that is on the #AM3H340 that you referenced, 205/65-10. As long as the bolt pattern of your current hubs are 4 on 4 inch the wheels of this would bolt up…

view full answer...

Install Location for Kat's Block Heater for 2019 Jeep Cherokee with 2.4 Liter 4 Cylinder Engine

Product Page this Question was Asked From

Continue Researching