Replacement Follow Landing Gear Leg for 1998 Fleetwood Savanna 5th Wheel
Question:
The inside weld stop spacing is 11.5 inches and the outer tube length is 31.5 inches.
asked by: Craig
Helpful Expert Reply:
I have a few different options for you depending on the route you would like to take. However, regardless of which route you pursue you will need to take some measurements of your outer jack tube length and weld stop spacing. If you are handy and the bevel gear inside your jack leg is the only one that is damaged then you can just obtain the Follow Jack Repair Kit for Stromberg Carlson Landing Gear part # LG-146060. However, if you don't want to mess with repairing your old jack leg or there is more internal damage than just the bevel gear then you will need to either replace the leg or the entire system.
The most likely replacement for just the leg is the Replacement Follow Jack w/ Drop Leg part # LG-179014 which has a 29-1/2" long outer tube and 15-1/2" weld stop spacing inside to inside or 17-1/2" weld stop spacing outside to outside. For a new system with the same outer tube length and weld stop spacing as the above we have the Stromberg Carlson Manual Landing Gear Set part # LG-183708.
I have attached a photo for you that shows how to measure the outer tube and weld stop spacing.
Mark C.
6/15/2020
I have a 37 ton log splitter with a jack that lifts as you lift the trailer itself by the handle. It's heavy. I want to replace the jack with one that allows a hand crank and wheel for moving it around. Does the weld on jack simply slip into place to replace this jack?
Products Referenced in This Question
Follow Jack Repair Kit for Stromberg Carlson Landing Gear
- Accessories and Parts
- Camper Jacks
- Trailer Jack
- Hardware
- Repair Kit
- Stromberg Carlson
more information >
Replacement Follow Jack w/ Drop Leg for Stromberg Carlson Landing Gear - 29-1/2"
- Accessories and Parts
- Camper Jacks
- Trailer Jack
- Legs
- Follow Leg
- Stromberg Carlson
more information >
Stromberg Carlson Manual Landing Gear Set - Weld On - 34-7/8" Lift - 8,000 lbs
- Camper Jacks
- Fifth Wheel Camper
- Leveling Jacks
- Stabilizer Jacks
- Steel
- 7001 - 8000 lbs
- Landing Gear
- Sidewind Jack
- 35 Inch Lift
- Weld-On
- 2 Jacks
- Stromberg Carlson
more information >
Stromberg Carlson Electric Landing Gear Set - Weld On - 34-7/8" Lift - 5,500 lbs
- Camper Jacks
- Fifth Wheel Camper
- Leveling Jacks
- Stabilizer Jacks
- Steel
- 5001 - 6000 lbs
- Electric Jack
- Landing Gear
- 35 Inch Lift
- Weld-On
- 2 Jacks
- Stromberg Carlson
more information >
Product Page this Question was Asked From
Landing Gear Set w/ Handle - 36-1/2" Lift - 8,000 lbs
- Camper Jacks
- Fifth Wheel Camper
- Leveling Jacks
- Stabilizer Jacks
- Steel
- 7001 - 8000 lbs
- Landing Gear
- Sidewind Jack
- 36 Inch Lift
- Weld-On
- 2 Jacks
- etrailer
more information >
Featured Help Information
Instructions
Continue Researching
- Q&A: Difference Between 8,000 lb Landing Gear RVLG-8HDL & RVLG-8000
- Q&A: How to Choose the Correct Replacement Landing Gear for 5th Wheel Trailer
- Q&A: Replacement Landing Gear Motor for a ADTH E226168
- Q&A: Troubleshooting Landing Gear Not Lifting 5th Wheel
- Article: Best Landing Gear
- Article: Trailer Wiring Diagrams
- Q&A: How to Measure to Pick Out Replacement Landing Gear for a Trailer
- Q&A: Bracket Dimensions of the etrailer RV Landing Gear System # RVLG-8HDL
- Q&A: How Much Fender Clearance Does The Brophy Heavy Duty Cable Camper Jacks Offer
- Article: Trailer Tire Sizing
- Article: Stability Control for Heavy Duty Vehicles
- Article: Our Team Picked The Best Camping Gear of the Year - Here Are Their Top Choices
- Article: Most Popular Wheel Bearings
- Article: How Much Solar Power Do I Need For My RV?
Craig
4/23/2019
The inside weld stop spacing is 11.5 inches and the outer tube length is 31.5 inches.