Replacement Crossbar for TracRac Cantilever Extension

Question

Question:

I need a crossbar for TRACRAC LADDER RACK EXTENSION

asked by: Fred

0

Expert Reply:

The replacement crossbar part # TAFX-30007-02 fits the Thule TracRac Cantilever extensions like the part # TH24001XT sso this would be what you'd need.

expert reply by: Jameson C

0

Answer 1

Hey Jason, I double checked with my contact at Thule and turns out you were right. The only difference is that the #8542526002 has a shallower top T-channel than the #TAFX-30007-02. Aside from that they are identical in size and length at…

view full answer...

Answer 2

I went down to the shop and double checked the crossbars and found that Thule made the mounting track on the bottom of the crossbar for the Thule TracRac TracONE Truck Bed Ladder Rack #TH27000XTB just different enough that it won't allow you…

view full answer...

Answer 3

We have a rubber wear strip that is designed to fit the top channel of the TracRac ladder rack crossbars as part #TARX-12007-1 which is 30 inches long. As far as a roller though we do not have anything that fits the bars that would work for this.

view full answer...

Answer 4

The correct top strip for the TracRac SR ladder racks is the part #TARX-12007-1 and the Thule #TH853354407 would not work.

view full answer...

Answer 5

The Replacement Crossbar for TracRac Ladder Racks - 69-1/2" Long - Qty 1 #TAFX-30007-02 compatible with your SR rack will use the end cap #TA01-27023. This threaded end cap will replace your missing end caps. The screw you will need for this…

view full answer...

Answer 6

For a replacement for the TracRac SR racks use #TAFX-30007-02 which is 69-1/2 inches long. It also fits TracOne, T-Rac Pro2, and UtilityRac SR ladder racks.

view full answer...

Answer 7

Because the Retrax PRO MX Tonneau Cover #RT80467 for the 2019 Chevy Silverado 2500 covers the bed rails, you would not be able to use a ladder rack like the Thule TracRac #TH27000XT since that rack requires the use of the bed rails. The only tonneau…

view full answer...

Answer 8

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 9

If your current springs have 5 leaves then going to a 7 leaf spring will increase the height of the trailer a little and make the trailer more susceptible to sway. Regarding capacity if you go with springs rated higher than what is required it will…

view full answer...

Answer 10

Seal 171255UC has an inner diameter of 1.719 inches and outer diameter of 2.565 inches. A seal that has those dimensions would actually be #58846. I've added a link to a video review of this seal for you to take a look at.

view full answer...

Answer 11

If your old axles have a 5 bolt brake flange the assemblies like Dexter Electric Trailer Brake Assembly - 12" - Left Hand - 6,000 lbs part #23-105 or Dexter Electric Trailer Brake Assembly - 12" - Right Hand - 6,000 lbs part #23-106 will…

view full answer...

Answer 12

Below is the general process for bleeding an electric over hydraulic brake actuator like #K71-650. Fill reservoir with NEW brake fluid. Never re-use brake fluid that has been salvaged or removed from another system. Remove the key from the breakaway…

view full answer...

Replacement Crossbar for TracRac Cantilever Extension

Products Referenced in This Question

Product Page this Question was Asked From

Featured Help Information

Instructions

Continue Researching