Rock Tamers Mud Flap # ERT00108 Weight

Question

Question:

What is the assembled weight ?

asked by: Ray

0

Expert Reply:

When assembled the Rock Tamers Heavy-Duty, Adjustable Mud Flap System for 2" Hitches # ERT00108 that you referenced weighs 34 lbs. I attached an install video link for this kit for you to check out as well.

expert reply by: Jameson C

0

Answer 1

The best solution for what you are wanting would be the RockTamers kit part #RT54FR which would fit on the 2-1/2 inch shank you have now. There isn't an easier to remove option than this as typically these kits don't get taken off and on with…

view full answer...

Answer 2

We offer weight distribution shanks for 2-inch and 2-1/2-inch hitches, shown on the linked page, but not one for a 3-inch hitch. We can still help you. Adding Curt reducer sleeve #C45408 allows dropping a 3-inch receiver down to either the 2-1/2-inch…

view full answer...

Answer 3

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 4

Since you have a wheelbase/axle spacing of 38 inches the correct hanger kit for slipper springs would be the part #HAP-105-205-01. And then for a 7k trailer axle the u-bolt kit you'd want would be the part #APUBR-8. I attached the diagram to use…

view full answer...

Answer 5

Bill yes, the Brass Tire Sensors for TST TPMS #TST-507-RV-S2 will work great with your TST TPMS for RVs - Color Display - Signal Booster #TST-507-RV-4-C. These sensors were designed specifically to be used with that system as well as the 6 sensor…

view full answer...

Answer 6

It could be a tow package fuse on the vehicle. Use the owners manual to find the locations of fuses/relays related to the tow package wiring to check them and replace as needed. If the issue is not a fuse or relay then you can test the vehicle side…

view full answer...

Answer 7

Since the issue appears to be on the vehicle side for your 2017 Toyota Tacoma, I recommend first checking the connector itself. Look to see if there is any dirt or corrosion built up inside the connector that may preventing a solid connection with…

view full answer...

Answer 8

The length of wire desired depends on your vehicle connection and your personal preference. You want enough slack for turning, but not so much for dragging as you mentioned. A little extra slack isn't a problem and not enough could lead to stress…

view full answer...

Answer 9

From what I could find it looks like your 122R (red) and 122Y (amber) lights measure 3.75" x 1.70" x .81". We don't have any replacement lense directly for the GLO-BRITE lights but we do have some similar lights that you could use…

view full answer...

Answer 10

Hello John. The #C96JR tail light kit for the 2023 Jeep Gladiator will indeed work with a Brake Buddy brake System Such as part #HM39524. So, if you plan to use a portable brake system, that is definitely what I recommend, and you do not need to get…

view full answer...

Answer 11

Thanks for the picture of what you have and the info you listed. The correct wheel you need is the part #AM20794 that you referenced.

view full answer...

Answer 12

I've never heard of an actual third brake light connector on a camper shell to plug in on a truck and we don't carry any parts to do that. The light generally needs to be hardwired into the truck's brake light circuit. The issue with this…

view full answer...

Rock Tamers Mud Flap # ERT00108 Weight

Product Page this Question was Asked From

Featured Help Information

Instructions

Miscellaneous Media

Continue Researching