Does Tow-Rax Aluminum Storage Cabinet # TWSP30CSA Have Wide Enough Bottom Shelf for Antifreeze Jug

Question

Question:

Is the bottom shelf tall enough for antifreeze jugs?

asked by: Joe

0

Expert Reply:

Yes, the bottom shelf of the Tow-Rax Aluminum Storage Cabinet # TWSP30CSA is deep enough to fit a standard antifreeze jug. In the picture I attached you'll see a car wash fluid jug in the bottom shelf which would be the same width.

expert reply by: Jameson C

0

click to enlarge

Answer 1

Thanks for reaching out, Sisco! The Tow-Rax Aluminum Storage Cabinet w/ Folding Tray #TWSP30CSA doesn't have a specific mounting kit since enclosed trailers vary greatly by construction. You'll need to either anchor it to wall supports or…

view full answer...

Answer 2

For attaching E-Track #e25VR or X-Track #3481788 on your walls of your enclosed trailer you will need to first determine how the walls are constructed. Adding plywood will help strengthen the mounts for the track depending on how spread apart the…

view full answer...

Answer 3

Since you have a wheelbase/axle spacing of 38 inches the correct hanger kit for slipper springs would be the part #HAP-105-205-01. And then for a 7k trailer axle the u-bolt kit you'd want would be the part #APUBR-8. I attached the diagram to use…

view full answer...

Answer 4

If your vehicle has a factory brake controller plug, you can simply use the Tekonsha Plug-In Wiring Adapter for Electric Brake Controllers – Ford, Item #3034-P, which will connect to the vehicle plug and the brake controller. On the new E-450…

view full answer...

Answer 5

To see all of the correct wheel and tire combos you'd need check out the link I attached. The option I would recommend is the part #TA43RR which is a Load Range C tire size ST175/80R13 mounted on a white spoke wheel with a bolt pattern of 5 on…

view full answer...

Answer 6

The manual lockout on your Atwood 85778 surge brake coupler is there so that you can back up the trailer without the brakes locking up on you. Yes you can safely tow your trailer with the broken manual lockout, you just have to make sure you…

view full answer...

Answer 7

While we may have an option for you, we do not have the exact specs on your Allis grease seal part number 5013 29772. However, with the 1.6" ID and 2.5" OD measurements you provides, that is very close to our #58846. This particular grease…

view full answer...

Answer 8

If you are needing the hub and drum assembly then you will want to go with the Dexter Trailer Hub and Drum Assembly #8-201-5UC3-EZ but if you are just looking for an idler hub then you will want part #8-213-5UC1 instead. These come with the correct…

view full answer...

Answer 9

I've never heard of an actual third brake light connector on a camper shell to plug in on a truck and we don't carry any parts to do that. The light generally needs to be hardwired into the truck's brake light circuit. The issue with this…

view full answer...

Answer 10

I did some checking and the hub/drum we offer that will work for you is the part #8-430-5UC3. This uses the same bearings as the 8-415 and will be an exact fit aside from the fact this is a non-ABS setup and the 8-415 came in an ABS setup and non-ABS…

view full answer...

Answer 11

I have a solution for you, but we do not carry Glo-Brite lights, so replacing it with the same brand will not be something I can offer you. Instead, to replace your Glo-Brite 9852-88, I recommend using the Optronics LED Trailer Tail Light #STL72RB.…

view full answer...

Answer 12

If the trailer wheels scrubbed (dragged and scrapped the ground instead of rolling) when jack knifed then it could have thrown something out of alignment or damaged something. First, inspect the suspension. Look for any elongated holes where…

view full answer...

Does Tow-Rax Aluminum Storage Cabinet # TWSP30CSA Have Wide Enough Bottom Shelf for Antifreeze Jug

Product Page this Question was Asked From

Continue Researching