What is the Replacement Hitch Cup Assembly 19-001056 Made of

Question

Question:

IS THIS CUP STEEL OR ALUMINUM??

asked by: Jake

0

Expert Reply:

The Replacement Hitch Cup Assembly for Ultra-Fab 5th Wheel King Pin Tripod Stabilizers part # UF19-001056 is made of aluminum. I called my contact Ultra-Fab to confirm this. This cup is used on both the Ultra-Fab 5th Wheel King Pin Tripod Stabilizers part # UF19-950001 and part # UF19-950200.

expert reply by: Conner L

0

Answer 1

The Replacement Hitch Cup Assembly for Ultra-Fab 5th Wheel King Pin Tripod Stabilizers part #UF19-001056 is a direct replacement for the Ultra-Fab 5th Wheel King Pin Tripod Stabilizer part #UF19-950001. In order to use the cup with another stabilizer…

view full answer...

Answer 2

Yes, the Hitch Cup Assembly #UF19-001056 can be used in place of the Ball Assembly #UF19-001057 on the Ultra-Fab Gooseneck Trailer Tripod Stabilizer #UF19-950450. This will effectively give you the 5th Wheel King Pin Tripod Stabilizer #UF19-950500.

view full answer...

Answer 3

I've never heard of an actual third brake light connector on a camper shell to plug in on a truck and we don't carry any parts to do that. The light generally needs to be hardwired into the truck's brake light circuit. The issue with this…

view full answer...

Answer 4

I did some checking and the hub/drum we offer that will work for you is the part #8-430-5UC3. This uses the same bearings as the 8-415 and will be an exact fit aside from the fact this is a non-ABS setup and the 8-415 came in an ABS setup and non-ABS…

view full answer...

Answer 5

Since you have a wheelbase/axle spacing of 38 inches the correct hanger kit for slipper springs would be the part #HAP-105-205-01. And then for a 7k trailer axle the u-bolt kit you'd want would be the part #APUBR-8. I attached the diagram to use…

view full answer...

Answer 6

The old version of the #HBA-CAM used 4 wires, but the product was updated awhile back and now uses only two wires as shown in the photo on the product description page. The white wire from the HBA-CAM would tap into the white ground wire and the blue…

view full answer...

Answer 7

What you're going to need is two of the transfer switches in that case. I have attached a diagram from Furrion that shows you how you're going to need to hook the two transfer switches #F30ATS up: -one to the other, then one branching off to…

view full answer...

Answer 8

If your current springs have 5 leaves then going to a 7 leaf spring will increase the height of the trailer a little and make the trailer more susceptible to sway. Regarding capacity if you go with springs rated higher than what is required it will…

view full answer...

Answer 9

You will need the Red LED Trailer Clearance or Side Marker Light #328-K-52 or Amber LED Trailer Clearance or Side Marker Light #328-K-51 for your 2018 Forest River Sunseeker motorhome. These lenses have the same Top Command SAE-AP2-16 markings on the…

view full answer...

Answer 10

The best option we offer for your dump trailer is the Erickson Mesh Tarp and Truck Bed Cover part #EM57059 which measures 12' wide x 16' long. It's not the exact dimensions you wanted but it will still cover most of the area you need it…

view full answer...

Answer 11

The 40 amp fuse for your 2006 Chevrolet Silverado tow package is used for the 12 volt battery charge circuit. This fuse is located toward the front of the underhood fuse box closest to the front auxiliary positive post (see photo). There may be a…

view full answer...

Answer 12

On a 2005 Chevy Silverado 1500, If you are facing the front of the truck looking at the power distribution box, there will be a post at the back left side and a fuse slot near it. It is that fuse slot that you will install a 30 amp fuse. I have…

view full answer...

What is the Replacement Hitch Cup Assembly 19-001056 Made of

Products Referenced in This Question

Product Page this Question was Asked From

Continue Researching