Removing the Rear Fascia of 2019 Cadillac XT4 to Install Curt Hitch # C39FR
Question:
How do I remove the rear Fascia? thanks
asked by: Tom D
Helpful Expert Reply:
For your 2019 Cadillac XT4 the Curt Trailer Hitch Receiver - Custom Fit - Class III - 2" # C39FR is the correct fit. The installation details state the following for removing the fascia:
a. Open the lift gate.
b. Remove the plastic cover next to the tail light (each side) by pulling upward to release the clips.
c. Using a T20 torx remove the screws connecting the fascia to the vehicle (each side).
d. Remove the wheel well trim using plastic fascia removal tools. Carefully pull the trim away from the vehicle enough to be able to remove the screw located behind.
e. Remove the screw located behind the wheel well trim with a 7mm socket.
f. Using a T15 torx remove screws in the wheel well liner, pull the liner away from the fascia.
g. Remove the hitch access panel in the middle of the fascia, using a T15 torx remove screws that hold the bottom of the fascia to the vehicle.
h. Starting from the wheel well area, carefully pull the fascia away from the vehicle (be careful not to pull it too far away from the vehicle to avoid damage) using plastic fascia removal tools to help release the clips along the way, work your way toward the middle from each wheel well. *CAUTION* Be extra careful at the taillight area, the fascia attachment is tight below the taillight and the bottom of the taillight is very sharp and will cause scratches to fascia if you’re not careful. Masking the bottom of the taillight is recommended. There are two clips to be released below the taillight See Fig. 2. Unplug the electrical connectors from behind the fascia. Set fascia aside for reinstallation. Keep the fasteners for reinstallation.
Product Page this Question was Asked From
Curt Trailer Hitch Receiver - Custom Fit - Class III - 2"
- Trailer Hitch
- Custom Fit Hitch
- Class III
- 4000 lbs GTW
- 2 Inch Hitch
- CURT
more information >
Featured Help Information
Instructions
Miscellaneous Media
Continue Researching
- Shop: Trailer Hitch
- Shop: Draw-Tite Max-Frame Trailer Hitch Receiver - Custom Fit - Class III - 2"
- Shop: Composite Trim Removal Tool Kit - 5 Piece
- Video: Best 2022 Cadillac XT4 Trailer Hitch Options
- Q&A: Is Fascia Trimming Required to Install Curt Trailer Hitch on 2020 Cadillac XT4
- Shop: Trailer Wiring
- Shop: T-One Vehicle Wiring Harness with 4-Pole Flat Trailer Connector
- Shop: Curt Trailer Hitch Receiver - Custom Fit - Class III - 2"
- Shop: Mounting Bracket 4-Pole Flat
- Video: Draw-Tite Max-Frame Trailer Hitch Installation - 2020 Cadillac XT4
- Shop: Mud Flaps
- Video: Choosing the Right Trailer Wiring
- Shop: Curt Powered Tail Light Converter with 4-Pole Flat Trailer Connector
- Q&A: What is the Difference Between a Class II and a Class III Hitch?
- Article: Brake Controller 7- and 4-Way Installation Kit (ETBC7)
- Search Results: 25580
- Search Results: dust cap
- Article: How to Choose the Right Trailer Hitch Class
- Shop: etrailer Hitch Pin Alignment Collar for Hitch Accessories - 2" Hitches
- Q&A: What is the Difference Between a 4-Way and 7-Way Trailer Connector
- Video: Tow Ready 4-Pole Mounting Bracket Installation
- Shop: Brake Controller
- Q&A: Replacement Clearance Lights Needed for GLO-BRITE 122R and 122Y Lights
- Article: Trailer Wiring Diagrams
- Search Results: 44649
- Video: Titan Trailer Brakes T2385200 Review
- Q&A: Recommended Lithium Battery Compatible Power Converter For Parallax 7355
- Search Results: 68149
- Video: etrailer Class III Trailer Hitch Installation - 2024 Subaru Crosstrek
- Article: My Trailer Hitch Doesn't Fit