Replacement Power Cord for Thomas Payne Momentum Recliners and Sofas

Question

Question:

Can I buy the power cord for the Thomas Payne electric Theater seats?

asked by: Brenda

0

Expert Reply:

You sure can! The replacement 12v power cord for the Thomas Payne Momentum RV Dual Reclining Sofa part 195-000055-056 is the Replacement 12V Cord for Thomas Payne Momentum Recliners and Sofas part # 195-387595.

expert reply by: Conner L

0

Answer 1

If the lights are not working on your Thomas Payne Momentum RV Dual Reclining Sofa 195-055-056-058 first just try unplugging it from your outlet. If that does not work you should unplug the 12V cords from the back of the sofa and then reconnect them.…

view full answer...

Answer 2

It sounds like you've got a Thomas Payne Seismic Dual Power Reclining RV Loveseat w Console, Heat, Massage, LEDs like the #195-091-092-090, and you need the power plug for it. In this case you'll want to use the Replacement Power Cord with…

view full answer...

Answer 3

I've never heard of an actual third brake light connector on a camper shell to plug in on a truck and we don't carry any parts to do that. The light generally needs to be hardwired into the truck's brake light circuit. The issue with this…

view full answer...

Answer 4

I did some checking and the hub/drum we offer that will work for you is the part #8-430-5UC3. This uses the same bearings as the 8-415 and will be an exact fit aside from the fact this is a non-ABS setup and the 8-415 came in an ABS setup and non-ABS…

view full answer...

Answer 5

Since you have a wheelbase/axle spacing of 38 inches the correct hanger kit for slipper springs would be the part #HAP-105-205-01. And then for a 7k trailer axle the u-bolt kit you'd want would be the part #APUBR-8. I attached the diagram to use…

view full answer...

Answer 6

The old version of the #HBA-CAM used 4 wires, but the product was updated awhile back and now uses only two wires as shown in the photo on the product description page. The white wire from the HBA-CAM would tap into the white ground wire and the blue…

view full answer...

Answer 7

To see all of the correct wheel and tire combos you'd need check out the link I attached. The option I would recommend is the part #TA43RR which is a Load Range C tire size ST175/80R13 mounted on a white spoke wheel with a bolt pattern of 5 on…

view full answer...

Answer 8

I have a solution for you, but we do not carry Glo-Brite lights, so replacing it with the same brand will not be something I can offer you. Instead, to replace your Glo-Brite 9852-88, I recommend using the Optronics LED Trailer Tail Light #STL72RB.…

view full answer...

Answer 9

The 40 amp fuse for your 2006 Chevrolet Silverado tow package is used for the 12 volt battery charge circuit. This fuse is located toward the front of the underhood fuse box closest to the front auxiliary positive post (see photo). There may be a…

view full answer...

Answer 10

On a 2005 Chevy Silverado 1500, If you are facing the front of the truck looking at the power distribution box, there will be a post at the back left side and a fuse slot near it. It is that fuse slot that you will install a 30 amp fuse. I have…

view full answer...

Answer 11

For your enclosed trailer application I have several suggestions for adding interior lighting that you can control directly via a switch. Since your current 4-pole trailer wiring does NOT include a 12V auxiliary power feed that could power inside…

view full answer...

Answer 12

The only way you could power interior dome lights on a trailer without it being connected to a tow vehicle would be to power the lights with a battery like a breakaway battery. How you choose to wire up the batteries will in the end be up to you, but…

view full answer...

Replacement Power Cord for Thomas Payne Momentum Recliners and Sofas

Product Page this Question was Asked From

Continue Researching