Is Adapter Fitting # T4871700 an Inverted Flare

Question

Question:

Does the 3/16 inch connector fit an inverted flare 3/16inch connector, such as on flexible brake line?

asked by: JJ

0

Expert Reply:

The adapter fitting # T4871700 is a 3/16 inch male inverted flare. The other end is a 1/4 inch and fits onto a 1/4 inch brake line so it can be attached to a 3/16 inch fitting

expert reply by: Charles S

0

Answer 1

Hello John thanks for your question. First off, I do like your choice of the Demco #DM5947 actuator for this application. Like you said, no reason to add a potential breaking point and it is heavy-duty enough to handle really anything your dump…

view full answer...

Answer 2

The male thread of the Replacement Adapter Fitting #T4871700 being longer would not be an issue when installing it in the back of the Dexter actuator part #K71-650. Pressure from the male side flare fitting to the actuator is what seals it so the…

view full answer...

Answer 3

I do have an option for you but I don't recommend stacking frame sections so you can bolt-on a new brake actuator. That said, it looks like you have an a-frame actuator and we have several options to replace this. The Demco Hydraulic Brake…

view full answer...

Answer 4

Personally I prefer the Demco Trailer Coupler #DM14976-52 with the composite handle over the Coupler #DM15791-81 with a metal handle. I feel it is easier to operate as it does not have the safety latch like you get on the metal handle. Since most…

view full answer...

Answer 5

For the Jayco RD-19 you would use the Demco Hydraulic Brake Actuator - Drum - Primed - A-Frame - Adjustable Channel Center - 8,000 lbs #DM8759522 and then the Demco Trailer Coupler - Cast - Adjustable Channel - eZ-Latch - Black - 2-5/16" Ball -…

view full answer...

Answer 6

The Reverse Lockout Solenoid for Demco Hydraulic Brake Actuators #DM11993 is the correct solenoid for your Demco Hydraulic Brake Actuator #DM8609101. The solenoid will fit Demco models DA10, DA20, and DA91. This solenoid has a non-bypass…

view full answer...

Answer 7

Sounds like what you need is the part #T4750200. This has thread fittings of 1/8" NPT female 1/2"-20 NPT male.

view full answer...

Answer 8

If you are talking about the small opening on the outside and inside of the Orifice Connector #T1209800 then those measure 0.0010" and 0.0865" respectfully. I went out to the warehouse and measured them with the digital caliper. Please note…

view full answer...

Answer 9

The part you are looking for is the Brass Connector for Titan Disc Brake Kit, #T4750300. This is the fitting that threads into the master cylinder that accepts the reverse lockout solenoid on your Titan actuator. I have attached a link to this part…

view full answer...

Answer 10

Adapter #T4871700 will allow you to use a 1/4 inch brake line and connect it to a 3/16 inch fitting. It is similar to #HS43-9035 in that you would thread in the brake lines.

view full answer...

Answer 11

The manual lockout on your Atwood 85778 surge brake coupler is there so that you can back up the trailer without the brakes locking up on you. Yes you can safely tow your trailer with the broken manual lockout, you just have to make sure you…

view full answer...

Answer 12

I checked with Curt and they do show the Curt Trailer Hitch Receiver part #C13233 as a fit for a 2022 Volvo XC90 All Models which includes the Recharge.

view full answer...

Is Adapter Fitting # T4871700 an Inverted Flare

Product Page this Question was Asked From

Continue Researching