Small Trailer Recommendation for Carrying ATV

Question

Question:

Im looking for a cargo trailer big enough for a four wheeler

asked by: Curtis Y

0

Expert Reply:

We have the Detail K2 Mighty Multi A-Frame Utility Trailer # K2MMT5X7 which was intended for applications like carrying an ATV that would work well for you. The inside dimensions are 52 inches wide by 88 inches long and has a payload capacity of 1,640 lbs.

expert reply by: Jameson C

0

Answer 1

Yes, the Wheel Masters Vision Plus Extendable Towing Mirrors - Strap On #WM6500's universal design will fit your 2015 Mercedes Benz ML 350. You will be able to mount this mirror to your front/passenger doors or front fenders.

view full answer...

Answer 2

The coupler on the Detail K2 Mighty Multi A-Frame Utility Trailer #K2MMT5X7 is for a 2" wide frame and has 3" on center bolt holes. The Curt QuickPin No-Latch Trailer Coupler #C82CR will bolt in place of the coupler that comes with…

view full answer...

Answer 3

The tire manufacturers state to fill the tires to their max pressure when cold and whatever pressure increase that happens as they warm up is perfectly fine and acceptable. If you inflate them to less than the max rating the capacity of the tire is…

view full answer...

Answer 4

The best and only option we have for transporting two trikes is using a utility trailer like the #K2MMT4X6 (6 feet long) or #K2MMT5X7 (7-1/2 feet long). For attachment straps to secure your bikes, I recommend ratchet straps like the Erickson…

view full answer...

Answer 5

Due to the size and length of your Anywhere Fat Tire Electric Trike, there is not going to be a cargo carrier that'll accommodate your trike. Instead, I believe the best option for you is to use a utility trailer, like the: -Detail K2 Mighty…

view full answer...

Answer 6

For a solution that will allow you to transport both bikes, your best bet is a utility trailer like the Detail K2 Mighty Multi Utility Trailer - 6' Long #K2MMT4X6 or the 7" long #K2MMT5X7. With these trailers, you need a ball mount/2"…

view full answer...

Answer 7

I've never heard of an actual third brake light connector on a camper shell to plug in on a truck and we don't carry any parts to do that. The light generally needs to be hardwired into the truck's brake light circuit. The issue with this…

view full answer...

Answer 8

I did some checking and the hub/drum we offer that will work for you is the part #8-430-5UC3. This uses the same bearings as the 8-415 and will be an exact fit aside from the fact this is a non-ABS setup and the 8-415 came in an ABS setup and non-ABS…

view full answer...

Answer 9

Since Demco uses 3,500 drum brake assemblies part #DMSB24429M and #DMSB24428M what you'd need is similar 3,500 electric brake assemblies like the etrailer part #AKEBRK-35L-SA for the left hand side and #AKEBRK-35R-SA for the right hand side. To…

view full answer...

Answer 10

What you're going to need is two of the transfer switches in that case. I have attached a diagram from Furrion that shows you how you're going to need to hook the two transfer switches #F30ATS up: -one to the other, then one branching off to…

view full answer...

Answer 11

If you are needing the hub and drum assembly then you will want to go with the Dexter Trailer Hub and Drum Assembly #8-201-5UC3-EZ but if you are just looking for an idler hub then you will want part #8-213-5UC1 instead. These come with the correct…

view full answer...

Answer 12

The old version of the #HBA-CAM used 4 wires, but the product was updated awhile back and now uses only two wires as shown in the photo on the product description page. The white wire from the HBA-CAM would tap into the white ground wire and the blue…

view full answer...

Small Trailer Recommendation for Carrying ATV

Product Page this Question was Asked From

Featured Help Information

Instructions

Miscellaneous Media

Continue Researching