Replacement Jam Nut for 19F0J Wheel Liners

Question

Question:

My wheel studs are 3/4”. I ordered the 19f0j which has approximately 1/2” threads. I can’t find the specs on it.

asked by: Gary

0

Expert Reply:

Since you said you ordered the 19F0J wheel liners then you need part # WM9073 instead as this is the correct fit for them and not the # WM9072F.

expert reply by: Jameson C

0

Answer 1

Currently the Replacement Center Cap #NA9130 is the only part that is separate from the Namsco Wheel Liners #NA226H40N for your Workhorse Chassis.

view full answer...

Answer 2

The Replacement Jam Nut #WM9072F that you referenced does look similar to the jam nuts that you are currently using to secure your Wheel Masters cover. To determine if they will fit your application though you need to measure your bolt size. This jam…

view full answer...

Answer 3

We have three wheel liners that sound like what you may have on your Monaco. You'll need to make sure they fit the rims you have before purchasing. #NA226H40N for 22-1/2 by 6-3/4 inch rims #NA227H40 for 22-1/2 by 7-1/2 inch rims. Direct fit on…

view full answer...

Answer 4

To know if the Phoenix USA Lug Nut Cover for 33mm Lug Nuts #PXSP33 will fit the lug nuts on your 2021 Tiffin Allegro Bus Motorhome you'll need to measure the diameter of the lug nuts. This lug nut cover fits 33mm lug nuts. If you find a different…

view full answer...

Answer 5

The Replacement Jam Nut #WM9073 referenced in your question is designed to replace those for the Wheel Masters 19J0J series liners. Based on the pictures I was able to pull up of the wheel covers on the 2001 Holiday Rambler motorhomes these do appear…

view full answer...

Answer 6

The wires on your new taillights should be labeled. If they are not labeled then all you need to do is apply 12 volt power to each wire to see which function it activates. Then for the motorhome you will need to use a circuit tester and test each of…

view full answer...

Answer 7

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 8

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 9

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 10

The OEM prep package consists of 4 "pucks" in the bed of the truck that will allow you to drop in puck style hitches for easy installation and removal, that gives you a completely clear bed when not in use. The B&W Companion OEM 5th…

view full answer...

Answer 11

The difference between an load range C and load range D tire in the same size is the capacity and psi rating. The two tires will still have the same dimensions and fit on the same wheel. The D rated tire has a higher capacity. For a ST175/80D13 like…

view full answer...

Answer 12

Class I and Class II hitches both have a 1-1/4 inch receiver opening. The difference is that a Class I hitch has a lower tongue weight rating, usually 200 pounds and a lower towing rating, usually 2,000 pounds. A Class II hitch usually has a tongue…

view full answer...

Replacement Jam Nut for 19F0J Wheel Liners

Products Referenced in This Question

Product Page this Question was Asked From

Continue Researching