Trailer Hitch Installation On 2015 Mitsubishi Lancer GT
Question:
Hi. I have a 2015 Mitsubishi lancer gt and looking to see if I have to drill hole to install your hitch. Looking a your instructions it looks like I would on the passenger side. Thank you in advance.
asked by: Henry
Expert Reply:
The Draw-Tite Sportframe Trailer Hitch Receiver - Custom Fit - Class I - 1-1/4" # 24885 is a confirmed fit for your 2015 Mitsubishi Lancer GT as long as you don't have the dual exhaust. There is no drilling required to install this hitch. The installation instructions state you will need a jig saw, cut-off wheel, or die grinder for enlarging the hole already present in the frame for the carriage bolt and block on the passenger side.
I've attached the installation details which state this as well as give you the step by step directions.
If you will be using this hitch for light towing, I recommend ball mount # 3593 along with a hitch ball like # 19256 for a 1-7/8 inch ball or # 19258 for a 2 inch diameter ball. This ball mount can be used in the drop or rise position as needed for your trailer and comes with the hitch pin and clip. For trailer wiring, I recommend the T-One Vehicle Wiring Harness with 4-Pole Flat Trailer Connector # 118538 which easily installs behind your tail lights to the factory wiring and then connects to the vehicle battery for power. I've attached an article to assist with routing that power wire.
Products Referenced in This Question
T-One Vehicle Wiring Harness with 4-Pole Flat Trailer Connector
- Custom Fit Vehicle Wiring
- Trailer Hitch Wiring
- Powered Converter
- Custom Fit
- 4 Flat
- Tekonsha
more information >
1-7/8" Hitch Ball - 3/4" Diameter x 1-9/16" Long Shank - Chrome - 2,000 lbs
- Trailer Hitch Ball
- Trailer Hitch Ball
- Standard Ball
- Chrome-Plated Steel
- 1-7/8 Inch Diameter Ball
- 1-9/16 Inch Shank Length
- 3/4 Inch Diameter Shank
- 2000 lbs GTW
- Class I
- Class II
- Draw-Tite
more information >
2" Hitch Ball - 3/4" Diameter x 1-9/16" Long Shank - Chrome - 3,500 lbs
- Trailer Hitch Ball
- Trailer Hitch Ball
- Standard Ball
- Chrome-Plated Steel
- 2 Inch Diameter Ball
- 1-9/16 Inch Shank Length
- 3/4 Inch Diameter Shank
- 3500 lbs GTW
- Class I
- Class II
- Draw-Tite
more information >
Draw-Tite Drawbar for 1-1/4" Hitch - 2-1/8" Rise, 2-3/4" Drop - 6-5/8" Long - 2K
- Trailer Hitch Ball Mount
- Fixed Ball Mount
- No Ball
- 3/4 Inch Ball Hole Diameter
- Steel Shank - Gloss Black
- Drop - 3 Inch
- Rise - 2 Inch
- Fits 1-1/4 Inch Hitch
- 2000 lbs GTW
- Class I
- Draw-Tite
more information >
Product Page this Question was Asked From
Draw-Tite Sportframe Trailer Hitch Receiver - Custom Fit - Class I - 1-1/4"
- Trailer Hitch
- Custom Fit Hitch
- Class I
- 200 lbs TW
- 2000 lbs GTW
- 1-1/4 Inch Hitch
- Concealed Cross Tube
- Draw-Tite
more information >
Featured Help Information
Instructions
Miscellaneous Media
Continue Researching
- Shop: Trailer Hitch
- Shop: Draw-Tite Sportframe Trailer Hitch Receiver - Custom Fit - Class I - 1-1/4"
- Shop: Trailer Wiring
- Article: Routing the Power Wire for a Trailer Wiring Harness
- Search Results: trailer hitch
- Shop: Hitch Reducer 2" to 1-1/4" Trailer Hitch Receiver
- Video: Brophy Hitch Adapters - Hitch Reducer - HT02 Review
- Shop: Curt Powered Tail Light Converter with 4-Pole Flat Trailer Connector
- Shop: T-One Vehicle Wiring Harness with 4-Pole Flat Trailer Connector
- Q&A: Comparing Trailer Wiring Options for a 2008 to 2012 Mitsubishi Lancer
- Video: Choosing the Right Trailer Wiring
- Shop: Curt Trailer Hitch Receiver - Custom Fit - Class I - 1-1/4"
- Shop: Curt Tail Light Converter with 4-Way Flat Trailer Connector
- Search Results: trailer hitch wiring
- Search Results: wiring harness
- Shop: Performance Chip Tuners
- Shop: Draw-Tite Drawbar for 1-1/4" Hitch - 2-1/8" Rise, 2-3/4" Drop - 9-3/4" Long - 2K
- Search Results: 44649
- Article: Trailer Wiring Diagrams
- Q&A: 10k Dexter Replacement Hub for a 8-415
- Article: How to Choose the Right Trailer Hitch Class
- Search Results: 68149
- Video: Choosing the Right Brake Controller
- Q&A: Replacement Hub Needed for Lippert 122093 Hub on 5,200 lbs Axle
- Shop: Brake Controller
- Search Results: 25580
- Video: Lippert Solera Slider Slide-Topper Review
- Article: Brake Controller 7- and 4-Way Installation Kit (ETBC7)
- Q&A: Wiring a Camper Shell Third Brake Light on a 2017 Chevrolet Silverado
- Search Results: dust cap
Mason
6/14/2020
I have an aftermarket axle-back exhaust on my 2016 Mitsubishi Lancer GT, will this clear the increased muffler size? I still have my stock muffler just in case I have to find out the hard way for myself...