Is SewerSolution Macerator System SS01 Intended to be Left Installed

Question

Question:

With this attached, can I leave the gray water tank open all the time .

asked by: Eric E

0

Expert Reply:

The SewerSolution Macerator System # SS01 is designed for flushing black water tanks and hoses after dumping. The kit has a rotating brass jet nozzle that can be aimed up to rinse your valve and tank or aimed down to rinse the included discharge hose. It is not intended to remain installed continuously. Please refer to the linked videos to see how this item functions.

expert reply by: Adam R

0

Answer 1

There isn't a minimum pressure listed for the SewerSolution Macerator System for RV Waste Tanks #SS01 to be efficient. As long as the water source has pressure near standard water pressure this will work fine. The better the pressure the better…

view full answer...

Answer 2

There isn't a required water pressure to operate the SewerSolution Macerator System for RV Waste Tanks #SS01. If the water pressure you have is near standard water pressure the system will work, although the macerator will work better with higher…

view full answer...

Answer 3

I contacted SewerSolution and the inner diameter of the metal inlet on the hose of the SewerSolution Macerator System for RV Waste Tanks part #SS01 is 3/4" the outside diameter is 7/8".

view full answer...

Answer 4

We have quite a few different 3 inch waste valves that would work for you. For example, we have the Valterra Bladex Waste Valve Body #T1003VPM which has an aluminum T-handle on it for opening and closing.

view full answer...

Answer 5

I've never heard of an actual third brake light connector on a camper shell to plug in on a truck and we don't carry any parts to do that. The light generally needs to be hardwired into the truck's brake light circuit. The issue with this…

view full answer...

Answer 6

I did some checking and the hub/drum we offer that will work for you is the part #8-430-5UC3. This uses the same bearings as the 8-415 and will be an exact fit aside from the fact this is a non-ABS setup and the 8-415 came in an ABS setup and non-ABS…

view full answer...

Answer 7

Since you have a wheelbase/axle spacing of 38 inches the correct hanger kit for slipper springs would be the part #HAP-105-205-01. And then for a 7k trailer axle the u-bolt kit you'd want would be the part #APUBR-8. I attached the diagram to use…

view full answer...

Answer 8

The two sizes you mentioned are pretty similar and fit many of the same 15 inch wheels. The 205/75-15 fits rim widths of 5 inch to 6-1/2 inch whereas the 225/75-15 fits widths that are 5 inch to 6 inch. The 205 is 27.1 inches tall and the 225 is 28.4…

view full answer...

Answer 9

You will need the Red LED Trailer Clearance or Side Marker Light #328-K-52 or Amber LED Trailer Clearance or Side Marker Light #328-K-51 for your 2018 Forest River Sunseeker motorhome. These lenses have the same Top Command SAE-AP2-16 markings on the…

view full answer...

Answer 10

If you are needing the hub and drum assembly then you will want to go with the Dexter Trailer Hub and Drum Assembly #8-201-5UC3-EZ but if you are just looking for an idler hub then you will want part #8-213-5UC1 instead. These come with the correct…

view full answer...

Answer 11

The old version of the #HBA-CAM used 4 wires, but the product was updated awhile back and now uses only two wires as shown in the photo on the product description page. The white wire from the HBA-CAM would tap into the white ground wire and the blue…

view full answer...

Answer 12

To see all of the correct wheel and tire combos you'd need check out the link I attached. The option I would recommend is the part #TA43RR which is a Load Range C tire size ST175/80R13 mounted on a white spoke wheel with a bolt pattern of 5 on…

view full answer...

Is SewerSolution Macerator System SS01 Intended to be Left Installed

Product Page this Question was Asked From

Featured Help Information

Miscellaneous Media

Continue Researching