Replacement Head Assembly for a Reese 16K 5th Wheel Hitch

Question

Question:

Does this assembly fit a Reese 16000?

asked by: Keith M

0

Expert Reply:

Yes, # RP30047A is the correct head and crossmember replacement for the Reese Fifth Wheel Hitch # RP30047.

expert reply by: Jon G

0

Answer 1

For your Reese Sliding Fifth Wheel Hitch #RP30051 we offer both a replacement head unit only, part #RP58146, or the head and crossmember assembly #RP30047A. You can choose the one that includes the mix of components you need. For the sliding legs you…

view full answer...

Answer 2

The T-One Vehicle Wiring Harness #118540 with it's single connector should be tapping into the vehicle stop/turn signals. If yours isn't active but the vehicle signals are working I'd first try unplugging and plugging the connectors in to…

view full answer...

Answer 3

The Tekonsha T-One Vehicle Wiring Harness #118540 referenced in your question is the correct harness and is confirmed to fit your 2013 Ford Explorer. The T-One connector will plug directly to the harness that is located beneath the rear of your…

view full answer...

Answer 4

There are many different wiring harnesses on Police Interceptors, and the photo you've attached is not a common fit for trailer wiring. I don't believe that harness is for your trailer wiring even though it looks similar. I've attached…

view full answer...

Answer 5

You can use the Tow Ready #118540 with no problems, as long as your Explorer is equipped with the connector shown in the photo I provided. The signals used at this connection point are already converted, so no additional converter is needed. This…

view full answer...

Answer 6

According to the installation instructions for the T-One Wiring Harness, #118540, the tow-plug for the 2016 Ford Explorer is located at the rear passenger's side. Refer to the attached photo. The trailer wiring harness will connect to this OEM…

view full answer...

Answer 7

Seal 171255UC has an inner diameter of 1.719 inches and outer diameter of 2.565 inches. A seal that has those dimensions would actually be #58846. I've added a link to a video review of this seal for you to take a look at.

view full answer...

Answer 8

I've never heard of an actual third brake light connector on a camper shell to plug in on a truck and we don't carry any parts to do that. The light generally needs to be hardwired into the truck's brake light circuit. The issue with this…

view full answer...

Answer 9

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 10

You will have to go with a sliding hitch to allow the trailer to make tight turns. For a trailer 8 feet wide the only bed length that's going to allow 90 degree turns without a slider is a stationary hitch. That being said you have two options.…

view full answer...

Answer 11

From what I could find it looks like your 122R (red) and 122Y (amber) lights measure 3.75" x 1.70" x .81". We don't have any replacement lense directly for the GLO-BRITE lights but we do have some similar lights that you could use…

view full answer...

Answer 12

I did some checking and the hub/drum we offer that will work for you is the part #8-430-5UC3. This uses the same bearings as the 8-415 and will be an exact fit aside from the fact this is a non-ABS setup and the 8-415 came in an ABS setup and non-ABS…

view full answer...

Replacement Head Assembly for a Reese 16K 5th Wheel Hitch

Products Referenced in This Question

Product Page this Question was Asked From

Featured Help Information

Instructions

Miscellaneous Media

Continue Researching