Replacement Powered Step Recommendation for 2007 Georgetown SE

Question

Question:

Recently steps got pulled off 2007 Georgetown se. All I have is step part number and controller number. See pictures

asked by: Thomas C

0

Expert Reply:

If you are looking for a replacement step setup the number on the step that I can see corresponds to a Lippert Kwikee 32 Series Electric Step # LC3722617 which is a powered double step for RVs like your 2007 Georgetown.

expert reply by: Jameson C

0

click to enlarge

Answer 1

I'd be happy to assist you. It sounds like you need the Sealed, Flush Mount Tall Rectangle LED Trailer Stop, Turn and Tail Light, Grommet and Plug, 12 Diode #STL34RB but most of the pictures I see have round tail lights like the Sealed, 4"…

view full answer...

Answer 2

I could not confirm the Lippert 32 Series Double Step Frame #LC3722618 (Lippert part 908032000) as the correct item for your application. My contact at Lippert did not recognize the OEM Frigette coach step that came on your Georgetown and he suggests…

view full answer...

Answer 3

For the replacement gear you will use the Replacement Entry Step Gear for Lippert Kwikee 25 and 26 Series Triple Steps #LC369354. I believe the shear pin you are referring to is a part of the gear itself. The motor is #LC369506 which comes with the…

view full answer...

Answer 4

The Lippert Components Kwikee Step Switch Magnet (1812971) #LC369299 is most likely what you need. I recommend the Lippert Components Kwikee Step 1 SWITCH PACK W/POWER SWITCH N/O (905325000) #LC369311 to give you the on/off switch as well in case you…

view full answer...

Answer 5

I've never heard of an actual third brake light connector on a camper shell to plug in on a truck and we don't carry any parts to do that. The light generally needs to be hardwired into the truck's brake light circuit. The issue with this…

view full answer...

Answer 6

I did some checking and the hub/drum we offer that will work for you is the part #8-430-5UC3. This uses the same bearings as the 8-415 and will be an exact fit aside from the fact this is a non-ABS setup and the 8-415 came in an ABS setup and non-ABS…

view full answer...

Answer 7

Since Demco uses 3,500 drum brake assemblies part #DMSB24429M and #DMSB24428M what you'd need is similar 3,500 electric brake assemblies like the etrailer part #AKEBRK-35L-SA for the left hand side and #AKEBRK-35R-SA for the right hand side. To…

view full answer...

Answer 8

What you're going to need is two of the transfer switches in that case. I have attached a diagram from Furrion that shows you how you're going to need to hook the two transfer switches #F30ATS up: -one to the other, then one branching off to…

view full answer...

Answer 9

Since you have a wheelbase/axle spacing of 38 inches the correct hanger kit for slipper springs would be the part #HAP-105-205-01. And then for a 7k trailer axle the u-bolt kit you'd want would be the part #APUBR-8. I attached the diagram to use…

view full answer...

Answer 10

You will need the Red LED Trailer Clearance or Side Marker Light #328-K-52 or Amber LED Trailer Clearance or Side Marker Light #328-K-51 for your 2018 Forest River Sunseeker motorhome. These lenses have the same Top Command SAE-AP2-16 markings on the…

view full answer...

Answer 11

If your current springs have 5 leaves then going to a 7 leaf spring will increase the height of the trailer a little and make the trailer more susceptible to sway. Regarding capacity if you go with springs rated higher than what is required it will…

view full answer...

Answer 12

I have a solution for you, but we do not carry Glo-Brite lights, so replacing it with the same brand will not be something I can offer you. Instead, to replace your Glo-Brite 9852-88, I recommend using the Optronics LED Trailer Tail Light #STL72RB.…

view full answer...

Replacement Powered Step Recommendation for 2007 Georgetown SE

Products Referenced in This Question

Product Page this Question was Asked From

Continue Researching