Install Bracket Recommendation for SnowBear Plow on 2006 Jeep Wrangler

Question

Question:

Hi, I have a snow bear electric lift snow plow purchased in 2003 that came off a 1995 Toyota Tacoma. I want to put it on my 2006 Jeep Wrangler using the SB397-010 brackets. Will these brackets work for the electric lift snow plow? My other questions is will the mounting holes from my old cross member line up with the new brackets for my jeep? I know the cross member is to long but I plan on cutting it to the right length and welding it? Thank you.

asked by: Mike

0

Expert Reply:

SnowBear plows either install to a vehicle with mounting brackets or a front hitch. Since it sounds like your plow uses brackets the correct kit for your 2006 Jeep Wrangler would be the part # SB397-010. If you needed a hitch though the correct hitch would be the # C31028 instead.

expert reply by: Jameson C

0

Answer 1

We have the Blue Ox Universal Bolt-On Adapters #BX88266 that will work with the Blue Ox Acclaim #BX4330. They need to be bolted on to a flat metal surface and if you're using your bumper it may need to be reinforced. I contacted Blue Ox and…

view full answer...

Answer 2

I've never heard of an actual third brake light connector on a camper shell to plug in on a truck and we don't carry any parts to do that. The light generally needs to be hardwired into the truck's brake light circuit. The issue with this…

view full answer...

Answer 3

The Trailer Leaf Spring, 2250 lbs. 6 Leaf, item #e27SR, is sold as a replacement spring for older trailers and measures 26 inches for eye to eye, center to center. If you are replacing the springs and hangers you will need to use the same center to…

view full answer...

Answer 4

Since Demco uses 3,500 drum brake assemblies part #DMSB24429M and #DMSB24428M what you'd need is similar 3,500 electric brake assemblies like the etrailer part #AKEBRK-35L-SA for the left hand side and #AKEBRK-35R-SA for the right hand side. To…

view full answer...

Answer 5

I would love to help you upgrade the suspension on your Twilight 2800 travel trailer. The MORryde Rubber Equalizers for Tandem Axle Trailers #MR87ZR that you referenced are a great solution but we do need to double check a few things. First is that…

view full answer...

Answer 6

From what I could find it looks like your 122R (red) and 122Y (amber) lights measure 3.75" x 1.70" x .81". We don't have any replacement lense directly for the GLO-BRITE lights but we do have some similar lights that you could use…

view full answer...

Answer 7

While we may have an option for you, we do not have the exact specs on your Allis grease seal part number 5013 29772. However, with the 1.6" ID and 2.5" OD measurements you provides, that is very close to our #58846. This particular grease…

view full answer...

Answer 8

The installation instructions for this product are recommended for individuals who have experience winding torsion springs. If you have not worked with a torsion spring system before, we recommend contacting a local garage door company to install…

view full answer...

Answer 9

My contact at Yates Rubber advises that a nominal 8-inch keel roller does not measure exactly 8 inches; typically they are slightly smaller than the specified size, much the way a piece of 2 x 4 lumber is not exactly 2-inches by 4-inches. I took…

view full answer...

Answer 10

The amount of bow that's put into trailer axles like the #7359765 is based on about how much a trailer is typically going to weigh that has a 3,500 lb capacity. So there's a bit of approximation and obviously it can't be totally perfect…

view full answer...

Answer 11

I did some checking and the hub/drum we offer that will work for you is the part #8-430-5UC3. This uses the same bearings as the 8-415 and will be an exact fit aside from the fact this is a non-ABS setup and the 8-415 came in an ABS setup and non-ABS…

view full answer...

Answer 12

By "mobile home type bolt pattern" I believe you are talking about a 5 spoke utility bolt pattern such as what is on the Dexter Trailer Hub and Drum Assembly - 6,000-lb and 7,000-lb Axles #8-174-5UC3. To measure your axle from hub face to…

view full answer...

Install Bracket Recommendation for SnowBear Plow on 2006 Jeep Wrangler

Products Referenced in This Question

Product Page this Question was Asked From

Featured Help Information

Instructions

Continue Researching